SCA02810-TFN-LRN Shelly, Inc., SCA02810-TFN-LRN Datasheet
SCA02810-TFN-LRN
Related parts for SCA02810-TFN-LRN
SCA02810-TFN-LRN Summary of contents
Page 1
... INNOVATIVE DISPLAY TECHNOLOGIES I RVINE P: 949-417-8070/F: 949-417-8075 E-mail: Website: Part Number : Customer APPROVED BY: ( FOR CUSTOMER USE ONLY ) SOLD BY APPROVED BY 17171 M A URPHY VENUE , C 92614-5915 ALIFORNIA info@shellyinc.com www.shellyinc.com Specification SCA02810-TFN-LRN : PCB VERSION: CHECKED BY DATE: ISSUE DATE ...
Page 2
NO. 1. Cover 2. Record of Revision 3. LCD Module Physical Data 4. External Dimensions 5. Block Diagram 6. Absolute Maximum Ratings 7. Electrical Characteristics 8. Touch Screen Panel Specifications 9. Interface PIN Connections 10. Recommend Initial Code 11. Electro-Optical ...
Page 3
DATE PAGE 10/30/09 3 RECORD OF REVISION SUMMARY Added version # A802 ...
Page 4
LCD MODULE PHYSICAL DATA General Description Size Display Type Display Mode Viewing Direction Connection Type Operation temperature Storage temperature Driving IC Mechanical Description Item Number of dots LCM dimension TP outline TP Viewing area TP Active area ...
Page 5
EXTERNAL DIMENSIONS . . ...
Page 6
BLOCK DIAGRAM TFT-LCD Module (Interface System Structure) RESET DB0 DB17 VDD VDDI GND Black Light Unite G2 LCD 240(RGB)*320 G320 ILI9325C G1 G319 ...
Page 7
Touch Screen Panel(Top View)(The TP ) ABSOLUTE MAXIMUM RATINGS Item Operating temperature Storage temperature Input voltage Supply voltage for logic Supply voltage for LCD NOTE the module is used above these absolute maximum ratings. It may ...
Page 8
ELECTRICAL CHARACTERISTICS DC Characteristics Vss= 0V, Ta= 25℃ Item Input high voltage Input low voltage Output high voltage Output low voltage Operating voltage Current consumption for LCD normal operation Back-Light unit Item Current CIE Brightness Luminance Uniformity ...
Page 9
TOUCH SCREEN PANEL SPECIFICATIONS 1.Electrical Characteristics Item Linearity Terminal Resistance Insulation Resistance Operating voltage Response Time Transmittance Note not operate it with a thing except a polyacetal pen(tip R0.8mm or less finger, especially those ...
Page 10
INTERFACE PIN CONNECTIONS NO. Symbol 1 VDD 2 VDDI 3 RESET GND 9 IM0 10 IM1 11 DB0 DB1 12 DB2 13 DB3 14 DB4 15 DB5 16 DB6 17 ...
Page 11
RECOMMEND INITIAL CODE void initial() { reset=0; delay(10); reset=1; delay(10); //************* Start Initial Sequence **********// write_command(0x0001);write_data(0x0100); // set SS and SM bit write_command(0x0002);write_data(0x0700); // set 1 line inversion write_command(0x0003);write_data(0x1030); // set GRAM write direction and BGR=1. write_command(0x0004);write_data(0x0000); // Resize ...
Page 12
Set GRAM area ---------------// write_command(0x0050);write_data(0x0000); // Horizontal GRAM Start Address write_command(0x0051);write_data(0x00EF); // Horizontal GRAM End Address write_command(0x0052);write_data(0x0000); // Vertical GRAM Start Address write_command(0x0053);write_data(0x013F); // Vertical GRAM Start Address write_command(0x0060);write_data(0xA700); // Gate Scan Line write_command(0x0061);write_data(0x0001); ...
Page 13
ELECTRO-OPTICAL CHARACTERISTICS Driving condition: VDD=2.8V, I Item Light angle（°） Temp（°C） Symbol Transmittance 0 Contrast ratio 0 Brightness 0 Luminance uniformity 0 (surface within panel) Cross talk 0 Rｘ Rｙ Gｘ Gｙ Chromaticity 0 Bｘ Bｙ Wｘ Wｙ Color Reproduction ...
Page 14
Measuring procedure: Transmittance: The light source is located at the backside of the panel. 1、 Measure the light source 2、 Place the LCD panel in front of the light source. Measure the luminance on the LCD panel surface Definitions Lv ...
Page 15
H, V: Active Area Uniformity value (Lu): min max( ) (4).CROSS-TALK Introduction： Crosstalk is an effect where the contrast of a display pixel is influenced by the state of the related pixels. A measure for this effect is ...
Page 16
Measuring procedure： Adaptation of the display to the highest contrast ratio (CR = LvA/LvC) as defined by the test patterns and a test area dots. Measurement of Luminance with test point A, B. Determination of ...
Page 17
Color Gamut definition 1000 Where blue red blue blue green ...
Page 18
INSPECTION CRITERION This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM. 1 Sample plan Sampling method shall be in accordance with MIL-STD-105D, inspection level II and based on: Major defect: AQL ...
Page 19
Inspection standards 4.1 Major Defect Item Items to be inspected display 4.1.1 All 2) Display abnormally functional defects 3) Missing vertical，horizontal segment 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting. 4.1.2 Missing Missing ...
Page 20
Cosmetic Defect Ite Items inspected No Line defect L(Length) Black line, White line, Foreign 4.2.2 material under polarizer, If the Polarizer scratch can be seen after mobile phone cover assembling or in the operating condition, judge ...
Page 21
Cosmetic Defect Item Items to be inspected No (i) Chips on corner Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. (ii)Usual surface cracks ...
Page 22
PRECAUTIONS FOR USING LCD MODULES Handing Precautions (1) The display panel is made of glass and polarizer. As glass is fragile, it tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. ...
Page 23
LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it. - ...
Page 24
Precautions for Operation (1) Viewing angle varies with the change of liquid crystal driving voltage (VLCD). Adjust VLCD to show the best contrast. ( indispensable condition to drive LCD's within the specified voltage limit since the higher ...