SCA04310-BFN-LRA Shelly, Inc., SCA04310-BFN-LRA Datasheet
SCA04310-BFN-LRA
Related parts for SCA04310-BFN-LRA
SCA04310-BFN-LRA Summary of contents
Page 1
... INNOVATIVE DISPLAY TECHNOLOGIES Irvine, California 92614-5915 P: 949-417-8070/F: 949-417-8075 E-mail: Website: Part Number : SCA04310-BFN-LRA Customer APPROVED BY: ( FOR CUSTOMER USE ONLY ) SOLD BY APPROVED BY 17171 Murphy Avenue info@shellyinc.com www.shellyinc.com Specification : PCB VERSION: DATE: CHECKED BY A401T ISSUE DATE ...
Page 2
NO. 1. Cover 2. Record of Reversion 3. LCD Module Physical Data 4. External Dimensions 5. Block Diagram 6. Absolute Maximum Ratings 7. Electrical Characteristics 8. Touch Screen Panel Specifications 9. Interface PIN Connections 10. Electro-Optical Characteristics 11. Inspection Criterion ...
Page 3
DATE PAGE 9/30/ RECORD OF REVISION Version A401T SUMMARY ...
Page 4
LCD MODULE PHYSICAL DATA General Description Display Type Display Mode Viewing Direction Connection Type Operation temperature Storage temperature Driving IC Mechanical Description Item Number of dots LCM dimension TP viewing area TP active area Active area ...
Page 5
EXTERNAL DIMENSIONS ...
Page 6
BLOCK DIAGRAM DISP PCLK DE HSYNC VSYNC R0-R7 G0-G7 B0-B7 DISP DE VDD GND Black Light Unite Touch Screen Panel(Top View) G2 LCD 480(RGB)*272 G272 HX8257 G1 G271 ...
Page 7
ABSOLUTE MAXIMUM RATINGS Item Operating temperature Storage temperature Power Supply Voltage NOTE the module is used above these absolute maximum ratings. It may become permanently damaged. Using the module within the following electrical characteristic conditions are ...
Page 8
ELECTRICAL CHARACTERISTICS DC Characteristics Item Input high voltage Input low voltage Supply voltage(1) Supply voltage(2) Logic dynamic current Driver dynamic current Back-Light unit Item Current CIE Brightness Luminous Uniformity Ratio Bezel(BE) must be connected to ground ...
Page 9
TOUCH SCREEN PANEL SPECIFICATIONS 1.Electrical Characteristics Item Linearity Terminal Resistance Insulation Resistance Operating voltage Response Time Transmittance Note not operate it with a thing except a polyacetal pen(tip R0.8mm or less finger, especially ...
Page 10
INTERFACE PIN CONNECTIONS NO. Symbol 1 VLED- 2 VLED+ 3 GND 4 VDD ...
Page 11
ELECTRO-OPTICAL CHARACTERISTICS Driving condition: VDD=3.3V, I Item Light angle（°） Temp（°C） Symbol Transmittance 0 Contrast ratio 0 Brightness 0 Luminance uniformity 0 (surface within panel) Cross talk 0 Rｘ Rｙ Gｘ Gｙ Chromaticity 0 Bｘ Bｙ Wｘ Wｙ Color ...
Page 12
Measurement conditions: Measuring Equipment Measurement Point Diameter Measurement Point Location Light source Reflectance Plate Test pattern Contrast setting Measuring procedure: Transmittance: The light source is located at the backside of the panel. 1、 Measure the light source 2、 Place the ...
Page 13
Measure the luminance Li with the points in figure 1. Figure Active Area Uniformity value (Lu): min max( ) (4)．CROSS-TALK Introduction： Crosstalk is an effect where the contrast of ...
Page 14
W: The width of the rectangle in the following pictures; 5mm 2*w=10mm Pattern A ● Definitions： Cross Talk Value： CTV = |LvA - LvB| / LvA * 100% Where： LvA: Luminance measured with the centre test point of pattern A ...
Page 15
Definitions Panel color coordinates according the CIE colour system (CIE 1931). In general always requested to measure the X, Y and Z values. Here u´, v´ and L* are according CIE 1931 ...
Page 16
NTSC: =F (display)/F (NTSC’) NTSC’ primaries: Red Green Blue F (NTSC’) =74.42 12:00 9:00 6:00 Brightness x’ y’ 0.67 0.33 0.21 0.71 0.14 0.08 3:00 Brightness cure of selected segment B 2 Brightness curve of nonselected segment B 1 Driving ...
Page 17
INSPECTION CRITERION This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM. 1 Sample plan Sampling method shall be in accordance with MIL-STD-105D, inspection level II and based on: Major defect: ...
Page 18
Inspection standards 4.1 Major Defect Item Items to be inspected No 4.1.1 All 1) No display functional 2) Display abnormally defects 3) Missing vertical，horizontal segment 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting. 4.1.2 Missing Missing ...
Page 19
Cosmetic Defect Item Items to be inspected No L(Length) Line defect Black line, Ignore White line, 4.2.2 Foreign L≤ 3.0 material under polarizer, L≤ 2.0 If the Polarizer scratch can be seen after mobile phone cover assembling or in ...
Page 20
Cosmetic Defect Item Items to be inspected No (i) Chips on corner Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. (ii)Usual surface cracks ...
Page 21
PRECAUTIONS FOR USING LCD MODULES Handing Precautions (1) The display panel is made of glass and polarizer. As glass is fragile. It tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. ...
Page 22
The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this protective film since static electricity may be generated （13）Since LCM has been assembled and adjusted with a high degree of ...