SCA03510-BFN-LNN Shelly, Inc., SCA03510-BFN-LNN Datasheet
SCA03510-BFN-LNN
Related parts for SCA03510-BFN-LNN
SCA03510-BFN-LNN Summary of contents
Page 1
... INNOVATIVE DISPLAY TECHNOLOGIES I RVINE P: 949-417-8070/F: 949-417-8075 E-mail: Website: Part Number : Customer APPROVED BY: ( FOR CUSTOMER USE ONLY ) SOLD BY APPROVED BY 17171 M A URPHY VENUE , C 92614-5915 ALIFORNIA info@shellyinc.com www.shellyinc.com Specification SCA03510-BFN-LNN : PCB VERSION: CHECKED BY DATE: ISSUE DATE ...
Page 2
NO. 1. Cover 2. Record Of Reversion 3. LCD Module Physical Data 4. External Dimensions 5. Block Diagram 6. Absolute Maximum Ratings 7. Electrical Characteristics 8. Interface PIN Connection 9. Recommend Initial Code 10. Electro-Optical Characteristics 11. Inspection Criterion 12. ...
Page 3
DATE PAGE 2008/12/12 P14 2009/10/30 P3 RECORD OF REVISION SUMMARY Update electro-optical characteristics Added version # 601 ...
Page 4
LCD MODULE PHYSICAL DATA General Description Display Type Display Mode Viewing Direction Connection Type Operation temperature Storage temperature Driving IC Mechanical Description Item Number of dots LCM dimension Active area Dot size Dot pitch Backlight The KEY ...
Page 5
EXTERNAL DIMENSIONS ...
Page 6
BLOCK DIAGRAM /RESET SPENA SPCUK SPDAT G0~G7 R0~R7 B0~B7 VCC AVSS GND G2 LCD 320(RGB)*240 G240 HX8238 G1 G239 ...
Page 7
ABSOLUTE MAXIMUM RATINGS Item Operating temperature Storage temperature Input voltage Supply voltage for logic NOTE the module is used above these absolute maximum ratings. It may become permanently damaged. Using the module within the following electrical characteristic ...
Page 8
ELECTRICAL CHARACTERISTICS DC Characteristics Vss= 0V, Ta= 25℃ Item Power supply: Current consumption for LCD normal operation Back-Light unit Item Current CIE Brightness Luminance Uniformity Ratio Bezel(BE) must be connected to ground of the main board Note: ...
Page 9
AC Characteristics ...
Page 10
...
Page 11
INTERFACE PIN CONNECTION ...
Page 12
NO. Symbol 1 VBL- 2 VBL- 3 VBL+ 4 VBL /RESET 9 SPENA(nCS) 10 SPCLK(SCL) 11 SPDAT(SDI ...
Page 13
HSYNC 37 VSYNC 38 DOLK(DOTCLK VCC 42 VCC ENB(DEN) 53 GND ...
Page 14
LCD_init(void) { Reset(); WriteCmd(0x0001);WriteData(0x633f); WriteCmd(0x0002);WriteData(0x0200); WriteCmd(0x0003);WriteData(0xa164); WriteCmd(0x0004);WriteData(0x0447); WriteCmd(0x0005);WriteData(0xfcd4); WriteCmd(0x000A);WriteData(0x4008); WriteCmd(0x000B);WriteData(0xc470); WriteCmd(0x000d);WriteData(0x123A); WriteCmd(0x000e);WriteData(0x2c00); WriteCmd(0x000f);WriteData(0x0000); WriteCmd(0x0016);WriteData(0x9f86); WriteCmd(0x0017);WriteData(0x2212); WriteCmd(0x001e);WriteData(0x00d0); WriteCmd(0x0030);WriteData(0x0507); WriteCmd(0x0031);WriteData(0x0004); WriteCmd(0x0032);WriteData(0x0707); WriteCmd(0x0033);WriteData(0x0000); WriteCmd(0x0034);WriteData(0x0000); WriteCmd(0x0035);WriteData(0x0307); WriteCmd(0x0036);WriteData(0x0405); WriteCmd(0x0037);WriteData(0x0703); WriteCmd(0x003a);WriteData(0x140B); WriteCmd(0x003b);WriteData(0x140B); } ELECTRO-OPTICAL CHARACTERISTICS //driver output //LCD driving waveform //power control 1 //input ...
Page 15
Driving condition: VDD=3.3V，Temperature =23℃±5℃，Humidity=60%±20%RH Item Light angle（°） Temp（°C） Symbol Transmissive 0 Contrast ratio 0 Brightness 0 Luminance uniformity 0 (surface within panel) Cross talk 0 Rｘ Rｙ Gｘ Gｙ Chromaticity 0 Bｘ Bｙ Wｘ Wｙ Color Reproduction 0 Area(NTSC) Tr ...
Page 16
Measuring Equipment Measurement Point Diameter Measurement Point Location Light source Reflectance Plate Test pattern Contrast setting Measuring procedure: Transmittance: The light source is located at the backside of the panel. 1、 Measure the light source 2、 Place the LCD panel ...
Page 17
Figure Active Area Uniformity value (Lu): min max (4)．CROSS-TALK Introduction： Crosstalk is an effect where the contrast of a display pixel is influenced by the state ...
Page 18
Pattern (valid for all greyscales): W: The width of the rectangle in the following pictures; 5mm 2*w=10mm Pattern A ● Definitions： Cross Talk Value： CTV = |LvA - LvB| / LvA * 100% Where： LvA: Luminance measured with the ...
Page 19
Definitions Panel colour coordinates according the CIE colour system (CIE 1931). In general always requested to measure the X, Y and Z values. Here u´, v´ and L* are according CIE 1931 ...
Page 20
Color Gamut Ratio (NTSC) related to NTSC’: NTSC: =F (display)/F (NTSC’) NTSC’ primaries: Red Green Blue F (NTSC’) =74.42 12:00 9:00 6:00 Brightness x’ y’ 0.67 0.33 0.21 0.71 0.14 0.08 3:00 Brightness cure of selected segment B 2 Brightness ...
Page 21
INSPECTION CRITERION This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM. 1 Sample plan Sampling method shall be in accordance with MIL-STD-105D, inspection level II and based on: Major defect: AQL ...
Page 22
Inspection standards 4.1 Major Defect Item Items to be inspected No 4.1.1 All 1) No display functional 2) Display abnormally defects 3) Missing vertical，horizontal segment 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting. 4.1.2 Missing Missing ...
Page 23
Cosmetic Defect Item Items to be inspected No Line defect L(Length) Black line, White line, Foreign 4.2.2 material under polarizer, If the Polarizer scratch can be seen after mobile phone cover assembling or in the operating condition, judge by ...
Page 24
Cosmetic Defect Item Items to be inspected No (i) Chips on corner Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. (ii)Usual surface cracks ...
Page 25
According to the <Acceptability of electronic assemblies> IPC-A-610C class 2 standard. Component missing or 4.3.7 SMT function defect are Major defect, the others are Minor defect. PRECAUTIONS FOR USING LCD MODULES (1) The display panel is made of glass ...
Page 26
To reduce the amount of static electricity generated, do not conduct assembling and other work under dry conditions. To reduce the generation of static electricity be ...
Page 27
Precautions for Operation (1) Viewing angle varies with the change of liquid crystal driving voltage (VLCD). Adjust VLCD to show the best contrast. ( indispensable condition to drive LCD's within the specified voltage limit since the higher ...