CY325 ETC, CY325 Datasheet - Page 64
CY325
Manufacturer Part Number
CY325
Description
Stepper System Controller
Manufacturer
ETC
Datasheet
1.CY325.pdf
(107 pages)
- Current page: 64 of 107
- Download datasheet (2Mb)
CY545 Stepper System Controller
www.ControlChips.com
wants to generate some output to the parallel interface. The CY545 then waits for the
IO_REQUEST signal to go low, indicating that the host system is ready for data. The data byte
is written to the data bus, and the BUSY signal is driven low. This indicates that data is available
to the host. When the host drives the IO_REQUEST signal high again, the bus is cleared, and
BUSY is brought back high also.
In the ASCII command mode, the FPL signal will continue to stay low as long as the CY545 has
data to generate. This is an indication that the host should continue reading data bytes from the
CY545. The FPL signal will be brought high when the CY545 writes a carriage return code,
indicating the end of the response.
In the Binary command mode, data may have any value, so each byte sent out will toggle the
FPL line back high again. When there are multiple bytes to send, the FPL signal will be brought
low as the CY545 is ready to generate the next data byte value.
This behavior is compatible with the CY233 LINC device, generating one message for query
responses in the ASCII mode, and one message per data byte in the Binary mode. A typical
query response waveform is shown below.
Immediate Commands
During External Memory Program Execution
The CY545B supports the acceptance and proper execution of immediate commands while
executing a program from external memory. However, the handshakes for this function are a
little more complex than the standard command handshake. More details are provided in this
section.
The FPL signal is very important in implementing the handshake protocol for immediate
commands, especially if the CY545 is also generating query responses or quoted messages
from the local memory program.
The FPL signal, driven by the CY545, can be used to control the direction of data on the CY545
local data bus. When FPL is high, the CY545 can accept command inputs, and when FPL is
low, the CY545 has output data for the parallel host.
© 2002 Cybernetic Micro Systems
59
Chapter 16 - Timing and Control
Related parts for CY325
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
E-Series RF 1:1 Transformer 1710 - 1910 MHz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
LINEAR INTEGRATED CIRCUITS 3-TERMINAL VOLATGE REGULATORS
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
Simple function, 50 to 600W DC-DC converters
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
FC050S6R5POWER MODULES: DC-DC CONVERTERS; 18 TO 36 VDC INPUT, 6.5VDC OUTPUT; 50 W TO 150W
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
Disk OnChip 2000 DIP
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
512K x 16Bit x 2Banks Synchronous DRAM
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
5-Bit Shift Register Product Specfication
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
2N191alloy-junction germanium transistors
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
RTL8139DREALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
M11B416256A-25J256 K x 16 DRAM EDO PAGE MODE
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
IFR3000IFR3500 Rx IF/BASEBAND PROCESSOR
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
78M08LINEAR INTEGRATED CIRCUITS 3-TERMINAL VOLATGE REGULATORS
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
CS4231A-KLPARALLEL INTERFACE MULTIMEDIA AUDIO CODEC
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
CS4231A-KQPARALLEL INTERFACE MULTIMEDIA AUDIO CODEC
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
BC41B143A05-IRK-E4BlueCpre 4-ROM Single Chip Bluetooth v2.0 System with EDR
Manufacturer:
ETC ETC
Datasheet: