AD9389/PCB Analog Devices, AD9389/PCB Datasheet - Page 31

• Manufacturer Part Number: AD9389/PCB
• Description: 800 MHz High Performance Hdmi/dvi Transmitter
• Manufacturer: Analog Devices

Hex
Address
0xB7
0xBA
0xBE
0xBF
0xC0
0xC1
0xC2
0xC3
0xC4
0xC5
0xC6
0xC7
Read/Write or
Read Only
Read/Write
Read
Read
Read
Read
Read
Read/Write
Read
Read
Read/Write
Read
Read
Bits
[7:0]
[6]
[5]
[4]
[7:5]
[4]
[3]
[7]
[6]
[5]
[4]
[3:2]
[1]
[0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7]
[6]
[5]
[4]
[3]
[2]
[1]
[0]
[4]
[3]
[2]
[1]
[0]
[7]
[6:0]
Default
Value
00000000
*0******
**0*****
***0****
000*****
***0****
****0***
0*** ****
*0** ****
**0* ****
***0 ****
**** 00**
**** **0*
**** ***0
00000000
00000000
00000000
00000000
00000000
0*******
*0******
**0*****
***0****
****0***
*****0**
******0*
*******0
***0****
****0***
*****0**
******0*
*******0
0*******
*0000000
00000000
Register Name
An_7
ENC_on
int_HDMI_MODE
keys_read_error
clk_delay
BCAPS
Repeater
KSV ready
Test bit
Test bit
HDCP support
Fast HDCP
BKSV1
BKSV2
BKSV3
BKSV4
BKSV5
EDID Segment
Error Flag
AN Stop
HDCP Enabled
EDID Ready Flag
I
RI Flag
BKSV Update Flag
PJ Flag
HDMI Mode
HDCP Requested
Rx Sense
EEPROM Read OK
TMDS Output Enabled
BKSV Flag
BKSV Count
2
C Interrupt
Rev. 0 | Page 31 of 48
Description
Byte 7 of An.
1 = the A/V content is being encrypted.
0 = not encrypted.
Default = 0.
Digital mode.
1 = HDMI mode.
0 = DVI mode.
1 = HDCP key reading error.
Edge select for input video clock.
011 = positive edge capture.
111 = negative edge capture.
Default = 000.
Must be written to 1 for proper operation.
Must be written to 0 for proper operation.
HDMI reserved.
HDCP repeater.
0 = HDCP receiver is not repeater capable.
1 = HDCP receiver is repeater capable.
KSV FIFO ready.
1 = HDCP receiver has compiled list of attached KSVs.
Must be written to 0 for proper operation.
Reserved.
HDCP 1.1 features support.
0 = HDCP receiver does not support version 1.1
features.
1 = HDCP receiver supports 1.1 features such as
enhanced encryption status signaling (EESS).
Fast authentication.
0 = HDCP Receiver not capable of fast authentication.
1 = HDCP Receiver capable of receiving unencrypted
video during the session re-authentication.
BKSV read from Rx by the HDCP controller 40 bits
(5 bytes).
Sets the E-DDC segment used by the EDID fetch
routine.
Error flag.
AN stop.
HDCP enabled.
EDID ready.
I
RI.
BKSV update.
PJ.
HDMI.
HDCP requested.
Rx sense.
EEPROM read.
TMDS output enabled.
BKSV flag.
BKSV count
2
C.
AD9389