LM3S5652 Luminary Micro, Inc, LM3S5652 Datasheet - Page 537
LM3S5652
Manufacturer Part Number
LM3S5652
Description
Lm3s5652 Arm Microcontroller
Manufacturer
Luminary Micro, Inc
Datasheet
1.LM3S5652.pdf
(703 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM3S5652-IQR50-A0
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S5652-IQR50-A0T
Manufacturer:
Texas Instruments
Quantity:
10 000
- Current page: 537 of 703
- Download datasheet (7Mb)
18.2.1.4 Scheduling
18.2.1.5 Additional Actions
June 02, 2008
After each packet has been unloaded, the RXRDY bit needs to be cleared in order to allow further
packets to be received. If the AUTOCL bit in the USBRXCSRHn register is set and a maximum-sized
packet is unloaded from the FIFO, the RXRDY bit is cleared automatically. For packet sizes less than
the maximum, RXRDY must be cleared manually. If the FULL bit was set when RXRDY is cleared,
the USB controller first clears the FULL bit. It then sets RXRDY again to indicate that there is another
packet waiting in the FIFO to be unloaded.
Note:
Special Bulk Handling
The packets transferred in bulk operations are defined by the USB specification to be 8, 16, 32, or
64 bytes in size. For some system designs, however, it may be more convenient for the application
software to read larger amounts of data from an endpoint in a single operation than can be transferred
in a single USB operation.
To simplify this case, the Stellaris
the packets received across the USB bus into larger data packets prior to being read by the
application software. With this option, the USBRXMAXPn register uses the bottom 11 bits to define
the payload for each individual transfer, while the top 5 bits define a multiplier. The USB controller
then combines the appropriate number of USB packets it receives into a single data packet of size
multiplier × payload within the FIFO before asserting RXRDY to alert the application software that a
packet in the FIFO is ready to be read. The size of the resulting packet is reported in the
USBRXCOUNTn register. From the application software’s point-of-view, the resulting operation
does not differ from the receipt of a single USB packet except in the size of the packet read.
Note:
The RXRDY bit is only set when either the specified number of packets have been received or a
“short” USB packet is received (that is, a packet of less than the specified payload for the endpoint).
If a protocol is being used in which the endpoint receives bulk transfers that are a multiple of the
recorded payload size with no short packet to terminate it, the USBRXMAXPn register should not
be programmed to expect more packets than there are in the transfer (otherwise, the software will
not be interrupted at the end of the transfer).
The device has no control over the scheduling of transactions as this is determined by the host
controller. The Stellaris
will wait for the request from the host controller and generate an interrupt when the transaction is
complete or if it was terminated due to some error. If the host controller makes a request and the
device controller is not ready, the USB controller sends a busy response (NAK) to all requests until
it is ready.
The USB controller responds automatically to certain conditions on the USB bus or actions by the
host controller: when the USB controller automatically stalls a control transfer and unexpected zero
length OUT data packets.
Double-packet buffering is disabled if an endpoint’s corresponding EPn bit is set in the
USBRXDPKTBUFDIS register. This bit is set by default, so it must be cleared to enable
double-packet buffering.
Packet-combining can only be used with bulk endpoints. The payload recorded in the
USBRXMAXPn register must also match the wMaxPacketSize field of the Standard
Endpoint Descriptor for the endpoint (see chapter 9 of the USB specification). The associated
FIFO must also be large enough to accommodate the combined data packet.
®
USB controller can set up a transaction at any time. The USB controller
®
USB controller includes a packet-combining feature that combines
Preliminary
LM3S5652 Microcontroller
537
Related parts for LM3S5652
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Inductor: Molded: 10u: 10%: 30M: 7.9: 440m: Axial: T/R
Manufacturer:
Inductor Supply, Inc.
Part Number:
Description:
Molded Inductor
Manufacturer:
Inductor Supply, Inc.
Datasheet:
Part Number:
Description:
Cree Smd Led
Manufacturer:
Cree, Inc.
Datasheet:
Part Number:
Description:
Cree Smd Led
Manufacturer:
Cree, Inc.
Datasheet:
Part Number:
Description:
Specification For Cotco Led Lamp
Manufacturer:
Marktech Optoelectronics
Datasheet:
Part Number:
Description:
Lm3s1110 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1133 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1138 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1150 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1162 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1165 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1332 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1435 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet: