sc3200 Advanced Micro Devices, sc3200 Datasheet - Page 141
![no-image](/images/manufacturer_photos/0/0/14/advanced_micro_devices_sml.jpg)
sc3200
Manufacturer Part Number
sc3200
Description
Geode-tm Sc3200 Processor
Manufacturer
Advanced Micro Devices
Datasheet
1.SC3200.pdf
(447 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
sc3200UCL-266
Manufacturer:
NS
Quantity:
5 510
Part Number:
sc3200UCL-266
Manufacturer:
NS/国半
Quantity:
20 000
- Current page: 141 of 447
- Download datasheet (4Mb)
SuperI/O Module
Master Error Detection
The ACB detects illegal Start or Stop Conditions (i.e., a
Start or Stop Condition within the data transfer, or the
acknowledge cycle) and a conflict on the data lines of the
ACCESS.bus. If an illegal condition is detected, ACBST[5]
is set, and master mode is exited (ACBST[1] is cleared).
Bus Idle Error Recovery
When a request to become the active bus master or a
restart operation fails, ACBST[5] is set to indicate the error.
In some cases, both the device and the other device may
identify the failure and leave the bus idle. In this case, the
start sequence may be incomplete and the ACCESS.bus
may remain deadlocked.
To recover from deadlock, use the following sequence:
1)
2)
3)
At this point, some of the slaves may not identify the bus
error. To recover, the ACB becomes the bus master: it
asserts a Start Condition, sends an address byte, then
asserts a Stop Condition which synchronizes all the slaves.
5.7.8
A slave device waits in idle mode for a master to initiate a
bus transaction. Whenever the ACB is enabled and it is not
acting as a master (i.e., ACBST[1] is cleared), it acts as a
slave device.
Once a Start Condition on the bus is detected, the device
checks whether the address sent by the current master
matches either:
• The ACBADDR[6:0] value if ACBADDR[7] = 1.
or
• The general call address if ACBCTL1[5] 1.
This match is checked even when ACBST[1] is set. If a bus
conflict (on ABD or ABC) is detected, ACBST[5] is set,
ACBST[1] is cleared and the device continues to search
the received message for a match.
If an address match or a global match is detected:
1)
2)
AMD Geode™ SC3200 Processor Data Book
Clear ACBST[5] and ACBCST[1].
Wait for a timeout period to check that there is no other
active master on the bus (i.e., ACBCST[1] remains
cleared).
Disable, and re-enable the ACB to put it in the non-
addressed slave mode. This completely resets the
functional block.
The device asserts its ABD pin during the acknowl-
edge cycle.
ACBCST[2] and ACBST[2] are set. If ACBST[0] = 1
(i.e., slave transmit mode) ACBST[6] is set to indicate
that the buffer is empty.
Slave Mode
3)
4)
Slave Receive and Transmit
Slave receive and transmit are performed after a match is
detected and the data transfer direction is identified. After a
byte transfer, the ACB extends the acknowledge clock until
the software reads or writes ACBSDA. The receive and
transmit sequences are identical to those used in the mas-
ter routine.
Slave Bus Stall
When operating as a slave, the device stalls the
ACCESS.bus by extending the first clock cycle of a trans-
action in the following cases:
• ACBST[6] is set.
• ACBST[2] and ACBCTL1[6] are set.
Slave Error Detection
The ACB detects illegal Start and Stop Conditions on the
ACCESS.bus (i.e., a Start or Stop Condition within the data
transfer or the acknowledge cycle). When this occurs,
ACBST[5] is set and ACBCST[3:2] are cleared, setting the
ACB as an unaddressed slave.
5.7.9
ABD and ABC Signals
The ABD and ABC are open-drain signals. The device per-
mits the user to define whether to enable or disable the
internal pull-up of each of these signals.
ACB Clock Frequency
The ACB permits the user to set the clock frequency for the
ACCESS.bus clock. The clock is set by the ACBCTL2[7:1],
which determines the ABC clock period used by the device.
This clock low period may be extended by stall periods initi-
ated by the ACB or by another ACCESS.bus device. In
case of a conflict with another bus master, a shorter clock
high period may be forced by the other bus master until the
conflict is resolved.
If ACBCTL1[2] is set, an interrupt is generated if both
ACBCTL1[2] and ACBCTL16 are set.
The software then reads ACBST[0] to identify the
direction requested by the master device. It clears
ACBST[2] so future byte transfers are identified as
data bytes.
Configuration
Revision 5.1
141
Related parts for sc3200
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![AM27S29DC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Advanced Micro Devices [4,096-Bit (512x8) Bipolar PROM]
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM27S29APC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Advanced Micro Devices [4,096-Bit (512x8) Bipolar PROM]
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM29BL802CB-70RZE](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Advanced Micro Devices [8 Megabit (512 K x 16-Bit) CMOS 3.0 Volt-only Burst Mode Flash Memory]
Manufacturer:
Advanced Micro Devices
Datasheet:
![M41000001Y](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
M41000001YAdvanced Micro Devices [32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory and 4 Mbit (512 K x 8-Bit/256 K x 16-Bit) Static RAM]
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM95C94JC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Advanced Burst Error Processor
Manufacturer:
Advanced Micro Devices
![AM7992BPC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Serial interface adapter (SIA)
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM9519ADC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Universal interrupt controller
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM27C256-150DC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
256 kilobit CMOS EPROM
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM9128-10PC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
2048 x 8 static RAM, 100ns
Manufacturer:
Advanced Micro Devices
Datasheet:
![P8284A](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Manufacturer:
Advanced Micro Devices
Datasheet:
![DM81LS98N](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Three-State Octal Buffers
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM2966PC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AM2966PCOctal Dynamic Memory Drivers with Three-State Outputs
Manufacturer:
Advanced Micro Devices
Datasheet:
![DM81LS97N](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Three-State Octal Buffers
Manufacturer:
Advanced Micro Devices
Datasheet:
![DM81LS96N](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Three-State Octal Buffers
Manufacturer:
Advanced Micro Devices
Datasheet:
![PAL16L8-7PC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
TTL programmable array logic, 7ns
Manufacturer:
Advanced Micro Devices
Datasheet: