pca9633 NXP Semiconductors, pca9633 Datasheet
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
pca9633
Manufacturer Part Number
pca9633
Description
Pca9633 4-bit Fm+ I2c-bus Led Driver
Manufacturer
NXP Semiconductors
Datasheet
1.PCA9633.pdf
(42 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
pca9633BS
Manufacturer:
NXP
Quantity:
42 000
Company:
Part Number:
pca9633BS
Manufacturer:
NXP
Quantity:
3 802
Company:
Part Number:
pca9633BSЈ¬118
Manufacturer:
NXP
Quantity:
17
Company:
Part Number:
pca9633DP1
Manufacturer:
NXP
Quantity:
51 000
Part Number:
pca9633DP1
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
pca9633DP2
Manufacturer:
NXP
Quantity:
30 000
Part Number:
pca9633DP2
Manufacturer:
NXP/恩智浦
Quantity:
20 000
1. General description
The PCA9633 is an I
Red/Green/Blue/Amber (RGBA) color mixing applications. Each LED output has its own
8-bit resolution (256 steps) fixed frequency Individual PWM controller that operates at
97 kHz with a duty cycle that is adjustable from 0 % to 99.6 % to allow the LED to be set
to a specific brightness value. A fifth 8-bit resolution (256 steps) Group PWM controller
has both a fixed frequency of 190 Hz and an adjustable frequency between 24 Hz to once
every 10.73 seconds with a duty cycle that is adjustable from 0 % to 99.6 % that is used to
either dim or blink all LEDs with the same value.
Each LED output can be off, on (no PWM control), set at its Individual PWM controller
value or at both Individual and Group PWM controller values. The LED output driver is
programmed to be either open-drain with a 25 mA current sink capability at 5 V or
totem-pole with a 25 mA sink, 10 mA source capability at 5 V. The PCA9633 operates with
a supply voltage range of 2.3 V to 5.5 V and the outputs are 5.5 V tolerant. LEDs can be
directly connected to the LED output (up to 25 mA, 5.5 V) or controlled with external
drivers and a minimum amount of discrete components for larger current or higher voltage
LEDs.
The PCA9633 is one of the first LED controller devices in a new Fast-mode Plus (Fm+)
family. Fm+ devices offer higher frequency (up to 1 MHz) and more densely populated bus
operation (up to 4000 pF).
The active LOW Output Enable input pin (OE) allows asynchronous control of the LED
outputs and can be used to set all the outputs to a defined I
state. The OE can also be used to externally PWM the outputs, which is useful when
multiple devices need to be dimmed or blinked together using software control. This
feature is available for the 16-pin version only.
Software programmable LED Group and three Sub Call I
groups of PCA9633 devices to respond to a common I
all red LEDs to be turned on or off at the same time or marquee chasing effect, thus
minimizing I
The PCA9633 is offered with 3 different I
(8-pin version), 4 different I
version), and 126 different I
version). They are software identical except for the different number of address
combinations.
The Software Reset (SWRST) Call allows the master to perform a reset of the PCA9633
through the I
their default state causing the outputs to be set HIGH (LED off). This allows an easy and
quick way to reconfigure all device registers to the same condition.
PCA9633
4-bit Fm+ I
Rev. 03 — 20 December 2006
2
2
C-bus commands.
C-bus, identical to the Power-On Reset (POR) that initializes the registers to
2
C-bus LED driver
2
C-bus controlled 4-bit LED driver optimized for
2
2
C-bus addresses from 2 programmable address pins (10-pin
C-bus addresses from 7 programmable address pins (16-pin
2
C-bus address options: fixed I
2
C address, allowing for example,
2
C addresses allow all or defined
2
C-bus programmable logic
Product data sheet
2
C-bus address