fdc37m707 Standard Microsystems Corp., fdc37m707 Datasheet - Page 64
![no-image](/images/no-image-200.jpg)
fdc37m707
Manufacturer Part Number
fdc37m707
Description
Fdc37m707 Enhanced Super I/o Controller With Wake-up Features
Manufacturer
Standard Microsystems Corp.
Datasheet
1.FDC37M707.pdf
(194 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 64 of 194
- Download datasheet (678Kb)
For both cases, and approximate two-byte
cushion is maintained from the beginning of the
sync field for the purposes of avoiding write
splices in the presence of motor speed variation.
For the Write Data case, the FDC activates
Write Gate at the beginning of the sync field
under the conventional mode.
then writes a new sync field, data address mark,
data field, and CRC as shown on page 57. With
the pre-erase head of the perpendicular drive,
the write head must be activated in the Gap2
field to insure a proper write of the new sync
field.
(WGATE = 1, GAP = 1), 38 bytes will be written
in the Gap2 space. Since the bit density is
proportional to the data rate, 19 bytes will be
written in the Gap2 field for the 500 Kbps
perpendicular mode (WGATE = 1, GAP =0).
It should be noted that none of the alterations in
Gap2 size, VCO timing, or Write Gate timing
affect normal program flow.
provided here is just for background purposes
and is not needed for normal operation. Once
the Perpendicular Mode command is invoked,
FDC software behavior from the user standpoint
is unchanged.
The perpendicular mode command is enhanced
to allow specific drives to be designated
Perpendicular
enhancement allows data transfers between
For the 1 Mbps perpendicular mode
recording
The information
drives.
The controller
This
64
Conventional and Perpendicular drives without
having to issue Perpendicular mode commands
between the accesses of the different drive
types,
compensation values.
When both GAP and WGATE bits of the
PERPENDICULAR MODE COMMAND are both
programmed to "0" (Conventional mode), then
D0, D1, D2, D3, and D4 can be programmed
independently to "1" for that drive to be set
automatically to Perpendicular mode.
mode the following set of conditions also apply:
1. The GAP2 written to a perpendicular drive
2. The write pre-compensation given to a
3. For
Note: Bits D0-D3 can only be overwritten when
Software
following
MODE COMMAND:
1. "Software" resets (via the DOR or DSR
2. "Hardware" resets will clear all bits
during a write operation will depend upon the
programmed data rate.
perpendicular mode drive will be 0ns.
conventional mode drives any data written
will be at the currently programmed write
pre-compensation.
registers) will only clear GAP and WGATE
bits to "0". D0-D3 are unaffected and retain
their previous value.
(GAP, WGATE and D0-D3) to "0", i.e all
conventional mode.
OW is programmed as a "1".If either
GAP or WGATE is a "1" then D0-D3 are
ignored.
nor
D0-D3
effect
and
having
hardware
on
programmed
to
the
change
resets
PERPENDICULAR
to
write
have
"0"
In this
pre-
the
for
Related parts for fdc37m707
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![USB2503-HZH](/images/no-image3.png)
Part Number:
Description:
Interface, Integrated USB2.0 Compatible 3-Port Hub
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![lan91c100fd](/images/no-image3.png)
Part Number:
Description:
Lan91c100fd Rev. B Feast Fast Ethernet Controller With Full Duplex Capability
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![lan91c100](/images/no-image3.png)
Part Number:
Description:
Feast ? Ast Ethernet Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![com20022i](/images/no-image3.png)
Part Number:
Description:
Com20022i 10 Mbps Arcnet Ansi 878.1 Controller With 2k X 8 On-chip Ram
Manufacturer:
Standard Microsystems Corp.
![lpc47n207-jv](/images/no-image3.png)
Part Number:
Description:
Lpc47n207 Lpc Super I/o Irda Hot Docking Chip With Uart Data Brief
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![lpc47s457-ns](/images/no-image3.png)
Part Number:
Description:
Advanced I/o With X-bus Interface
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![com81c17](/images/no-image3.png)
Part Number:
Description:
Twenty Pin Uart Tpuart Corporation
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![MSD7262](/images/no-image3.png)
Part Number:
Description:
Enhanced Small Device Interface Controller
Manufacturer:
Standard Microsystems Corp.
![EMC2301](/images/no-image3.png)
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC2302](/images/no-image3.png)
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1001](/images/no-image3.png)
Part Number:
Description:
Emc1001 1.5?c Smbus Temperature Sensor In Miniature Sot-23
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1043](/images/no-image3.png)
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Beta Compensation And Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1046](/images/no-image3.png)
Part Number:
Description:
1 Degree C Multiple Temperature Sensor With Beta Compensation And Hottest Of Thermal Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1053](/images/no-image3.png)
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Resistance Error Correction & Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1063](/images/no-image3.png)
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet: