w83l517g Winbond Electronics Corp America, w83l517g Datasheet - Page 22
w83l517g
Manufacturer Part Number
w83l517g
Description
Winbond Lpc I/o For Notebook W83l517d/ W83l517d-f
Manufacturer
Winbond Electronics Corp America
Datasheet
1.W83L517G.pdf
(133 pages)
- Current page: 22 of 133
- Download datasheet (864Kb)
THRESHOLD # × (1/DATA/RATE) *8 - 1.5 μS = DELAY
At the start of a command the FIFO is always disabled and command parameters must be sent based
upon the RQM and DIO bit settings in the main status register. When the FDC enters the command
execution phase, it clears the FIFO of any data to ensure that invalid data are not transferred.
An overrun and underrun will terminate the current command and the data transfer. Disk writes will
complete the current sector by generating a 00 pattern and valid CRC. Reads require the host to
remove the remaining data so that the result phase may be entered.
DMA transfers are enabled with the SPECIFY command and are initiated by the FDC by activating the
DRQ pin during a data transfer command. The FIFO is enabled directly by asserting DACK# and
addresses need not be valid.
Note that if the DMA controller is programmed to function in verify mode a pseudo read is performed
by the FDC based only on DACK#. This mode is only available when the FDC has been configured
into byte mode (FIFO disabled) and is programmed to do a read. With the FIFO enabled the above
operation is performed by using the new VERIFY command. No DMA operation is needed.
6.1.3
The function of the data separator is to lock onto the incoming serial read data. When a lock is
achieved the serial front end logic of the chip is provided with a clock which is synchronized to the
read data. The synchronized clock, called the Data Window, is used to internally sample the serial
data portion of the bit cell, and the alternate state samples the clock portion. Serial to parallel
conversion logic separates the read data into clock and data bytes.
The Digital Data Separator (DDS) has three parts: control logic, error adjustment, and speed tracking.
The DDS circuit cycles once every 12 clock cycles ideally. Any data pulse input will be synchronized
and then adjusted by immediate error adjustment. The control logic will generate RDD and RWD for
every pulse input. During any cycle where no data pulse is present, the DDS cycles are based on
speed. A digital integrator is used to keep track of the speed changes in the input data stream.
FIFO THRESHOLD
FIFO THRESHOLD
Data Separator
15 Byte
15 Byte
1 Byte
2 Byte
8 Byte
1 Byte
2 Byte
8 Byte
MAXIMUM DELAY TO SERVICING AT 500K BPS
MAXIMUM DELAY TO SERVICING AT 1M BPS
- 22 -
15 × 16 μS - 1.5 μS = 238.5 μS
15 × 8 μS - 1.5 μS = 118.5 μS
1 × 16 μS - 1.5 μS = 14.5 μS
2 × 16 μS - 1.5 μS = 30.5 μS
8 × 16 μS - 1.5 μS = 6.5 μS
2 × 8 μS - 1.5 μS = 14.5 μS
8 × 8 μS - 1.5 μS = 62.5 μS
1 × 8 μS - 1.5 μS = 6.5 μS
W83L517D/W83L517D-F
Data Rate
Data Rate
Related parts for w83l517g
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Winbond H/w Monitoring Ic
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Lpc I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Smbus Gpi/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel P4 Springdale Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel P4 Springdale Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel P4 Springdale Series Chipset P4 Springdale Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel P4 845 Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Via P4/kt Series Chipset
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Clock Generator For Intel 915/925 Chipsets
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond H/w Monitoring Ic
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Lpc I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond Smbus Gpi/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Winbond I/o
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
Pa-risc Embedded Controller
Manufacturer:
Winbond Electronics Corp America
Datasheet: