pdiusbh12 NXP Semiconductors, pdiusbh12 Datasheet
pdiusbh12
Related parts for pdiusbh12
pdiusbh12 Summary of contents
Page 1
... PDIUSBH12 USB 2-port hub Product specification Supersedes data of 1999 Feb 25 hilips Semiconductors INTEGRATED CIRCUITS 1999 Jul 22 ...
Page 2
... DIP – +85 C 1999 Jul 22 DESCRIPTION The Universal Serial Bus Hub PDIUSBH12 is a cost and feature optimized second generation USB Hub with 2 downstream ports and 3 embedded functions (compound hub normally used in any microcontroller-based system and communicates with the system ...
Page 3
... This is a conceptual block diagram and does not include each individual signal. 1999 Jul 22 12 MHz D– PLL BIT CLOCK RECOVERY FULL SPEED PHILIPS SIE END OF FRAME TIMERS 3 Product specification PDIUSBH12 INTEGRATED RAM MEMORY MANAGEMENT SLAVE INTERFACE UNIT GENERAL PORT CONTROLLER INTERRUPT ...
Page 4
... USB. Re-initialization of the USB bus connection can also be affected without requiring the pull out of the cable. The PDIUSBH12 will check for USB VBUS availability before the connection can be established. VBUS sensing is provided through OCURRENT_N pin. See the pin description for details. Sharing of ...
Page 5
... USB 2-port hub ENDPOINT DESCRIPTIONS There are two endpoint configuration modes supported by the PDIUSBH12, the Single Embedded Function mode and the Multiple (3) Embedded Function mode. The Single Embedded Function mode is the default at power up reset. The Multiple (3) Embedded Function mode can be configured by writing a zero to bit 7 of the first byte of the Set Mode command. Either mode is backward compatible to the PDIUSBH11. ...
Page 6
... LED pins as per port overcurrent condition pins. An overcurrent condition on any port can be uniquely identified in Mode 1. However, all downstream ports are disabled as a result of a single overcurrent condition. In addition to the two modes of operation, the PDIUSBH12 can also be configured to take either a 48 MHz crystal oscillator (for backward compatibility to PDIUSBH11 MHz crystal. ...
Page 7
... Connect to microcontroller interrupt 2 OD6 I C bi-directional data 2 OD6 I C bit-clock Ground reference + Downstream port 3 D connection – Downstream port 3 D connection + Downstream port 2 D connection - Downstream port 2 D connection Analog Ground reference Analog voltage supply 3.3V 0.3V + Upstream D connection - Upstream D connection 7 Product specification PDIUSBH12 ...
Page 8
... Connect to microcontroller interrupt 2 OD6 I C bi-directional data 2 OD6 I C bit-clock Ground reference + Downstream port 3 D connection – Downstream port 3 D connection + Downstream port 2 D connection - Downstream port 2 D connection Analog Ground reference Analog voltage supply 3.3V 0.3V + Upstream D connection - Upstream D connection 8 Product specification PDIUSBH12 ...
Page 9
... Memory Management Unit. If the RW bit in the address indicates a ‘master reads data from slave’ (=‘1’) the PDIUSBH12 will send data to the master. The I must acknowledge all data bytes except the last one. In this way the ...
Page 10
... Port 3 E9h Port 2 E0h Port 3 E1h F7h General Commands F6h F5h 10 Product specification PDIUSBH12 DATA PHASE Write 1 byte Write 1 byte Write 1 byte Write 1 byte Write 1 byte Write 2 bytes Read 2 bytes Read 1 byte (optional) Read 1 byte (optional) Read 1 byte (optional) Read 1 byte ...
Page 11
... Set Mode Command Data The Set Mode command is followed by two data writes. The first byte contains the configuration byte values. The second byte is the clock division factor byte. 11 Product specification PDIUSBH12 : D8h : Write 1 byte 1 0 POWER ON VALUE 0 0 HUB’S INTERRUPT ENDPOINT ...
Page 12
... When the 12 MHz input crystal frequency is selected, the reset value is 11. This will produce the lowest output frequency of 4 MHz which can then be programmed up by the user. The PDIUSBH12 design ensures no glitching during frequency change. The programmed value will not be changed by a bus reset. ...
Page 13
... The bus reset interrupt is internally cleared by reading the interrupt register. A bus reset is completely identical to the hardware reset through the RESET_N pin with the sole difference of interrupt notification. The hub interrupt endpoint is handled internally by the PDIUSBH12 hardware without the need of microcontroller intervention. 1999 Jul 22 Select Endpoint ...
Page 14
... Validate Buffer command. This indicates that the data in the buffer are valid and can be sent to the host when the next IN token is received. 14 Product specification PDIUSBH12 : F0h : Read multiple bytes (max 10 transaction (read the first 2 bytes ...
Page 15
... For these features, any of the Set / Clear Feature commands can be used. The specific port assignment is ignored. When the PDIUSBH12 is configured in mode 1, there is still only one power switch output but there are two individual overcurrent input pins corresponding to each port. This means that the F_PORT_POWER feature is port specific and the C_PORT_OVERCURRENT feature is not port specific ...
Page 16
... When reset is completed (nominal duration of 10 ms), this bit indicates a ‘0’. Power A ‘1’ indicates that power is supplied to downstream ports. Since the PDIUSBH12 supports gang mode power switching, this bit is the same for all ports. Low Speed A ‘1’ indicates that low speed device is connected to this port. This bit is only valid when Connect bit is a ‘ ...
Page 17
... Get Port Status command section. From these bits, the Status Change bit for the embedded function is derived (i.e. the port specific Status Change bits). This Status Change bit is then provided to the PDIUSBH12 by the Set Status Change Bits command. 1999 Jul 22 ...
Page 18
... See DC and AC characteristics per device TEST CONDITIONS V < Note 2 V > < Note < 8000 V. ESD(MAX) 18 Product specification PDIUSBH12 MIN MAX UNIT 3 – MIN MAX UNIT –0.5 +4.6 V – ...
Page 19
... IN 1 |(D+) – (D–)| Includes V range 1. 15k to GND L Pin to GND Steady state drive SoftConnect = ON Pull-down = ON 1.5k IS INTERNAL TEST POINT 50pF L 15k SV00849 19 Product specification PDIUSBH12 TYP MAX UNIT 0 1.9 V 1.5 V 0.7 V 0 MIN ...
Page 20
... Between 10% and 90% Between 10% and 90 Figure 1 Figure 1 Characterized and not tested. Guaranteed by design. Figure 1 Full Speed downstream port. Figure 2 Figure 2 Figure 3 HDD Figure 3 20 Product specification PDIUSBH12 MIN MAX UNIT 110 % 1.3 2.0 V 160 175 ns – – ...
Page 21
... 50pF 350pF Figure 1 Figure 1 Figure 1 Figure 1 Low Speed downstream port. Figure 2 Figure 2 Figure 3 HDD Figure 3 CROSSOVER POINT EXTENDED + t PERIOD DEOP 21 Product specification PDIUSBH12 MIN MAX UNIT 300 300 ns 80 120 % 1.3 2.0 V 1.25 1.50 s –40 100 ns 330 ns 675 ns ...
Page 22
... B. UPSTREAM EOP DELAY EOP– HDD – t EOPD HDD – t EOP+ EOP– , AND t LEOPDR LHESK Figure 3. Hub EOP Delay and EOP Skew 22 Product specification PDIUSBH12 CROSSOVER POINT CROSSOVER POINT Hub Delay Upstream t HDD B. UPSTREAM HUB DELAY SV00514 CROSSOVER POINT EXTENDED t t EOP– ...
Page 23
... BUF SDA t HD;STA 1999 Jul 22 TEST CONDITIONS BIT 0 BIT 6 LSB (A6) (R/W) t HIGH 1/f SCL SU;DAT HD;DAT VD:DAT 2 Figure 4. I C-bus timing diagram 23 Product specification PDIUSBH12 and V with an input voltage IL IH MIN MAX UNIT 1000 kHz 0.5 s 0.25 s 0.25 s 0.45 s 0.45 s 0.3 s 0.1 s 100 ...
Page 24
... Philips Semiconductors USB 2-port hub SO28: plastic small outline package; 28 leads; body width 7.5mm 1999 Jul 22 24 Product specification PDIUSBH12 SOT136-1 ...
Page 25
... Philips Semiconductors USB 2-port hub DIP28: plastic dual in-line package; 28 leads (600 mil) 1999 Jul 22 25 Product specification PDIUSBH12 SOT117-1 ...
Page 26
... Use a low-voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 26 Product specification PDIUSBH12 ...
Page 27
... Wave soldering is only suitable for SSOP and TSSOP packages with a pith (e) equal to or larger than 0.65 mm definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 1999 Jul 22 Soldering Method 1 Wave Reflow 2 suitable – not suitable suitable 3 not suitable suitable suitable suitable 4, 5 not recommended suitable 6 not recommended suitable 27 Product specification PDIUSBH12 Dipping suitable – – – – – ...
Page 28
... Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 hilips Semiconductors 1999 Jul 22 [1] Copyright Philips Electronics North America Corporation 1999 Document order number: 28 Product specification PDIUSBH12 All rights reserved. Printed in U.S.A. Date of release: 07-99 9397 750 06221 ...