attiny25v ATMEL Corporation, attiny25v Datasheet - Page 167

no-image

attiny25v

Manufacturer Part Number
attiny25v
Description
Microcontroller With 2/4/8k Bytes In-system Programmable Flash
Manufacturer
ATMEL Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
attiny25v-10MU
Manufacturer:
ATMEL
Quantity:
1 650
Part Number:
attiny25v-10MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
attiny25v-10PU
Manufacturer:
Atmel
Quantity:
29 497
Part Number:
attiny25v-10PU
Manufacturer:
Atmel
Quantity:
5 000
Part Number:
attiny25v-10SU
Manufacturer:
ATMEL
Quantity:
2 110
Part Number:
attiny25v-10SU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
attiny25v-15ST
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Table 21-1.
Notes:
2586K–AVR–01/08
Symbol
R
R
I
CC
RST
pu
(7)
1. Typical values at 25°C. Maximum values are characterised and not production test limits.
2. “Min” means the lowest value where the pin is guaranteed to be read as high.
3. “Max” means the highest value where the pin is guaranteed to be read as low.
4. Although each I/O port can sink more than the test conditions (10 mA at V
5. Although each I/O port can source more than the test conditions (10 mA at V
6. The RESET pin must tolerate high voltages when entering and operating in programming modes and, as a consequence,
7. All I/O modules are turned off (PRR = 0xFF) for all I
8. Brown-Out Detection (BOD) disabled.
conditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 60 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 60 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
has a weak drive strength as compared to regular I/O pins. See
(starting on
Parameter
Reset Pull-up Resistor
I/O Pin Pull-up Resistor
Power Supply Current
Power-down mode
DC Characteristics. T
page
188).
(8)
A
= -40°C to 85°C
Vcc =
Vcc =
Active 1MHz, V
Active 4MHz, V
Active 8MHz, V
Idle 1MHz, V
Idle 4MHz, V
Idle 8MHz, V
WDT enabled, V
WDT disabled, V
Condition
5.5
5.5
V, input low
V, input low
CC
CC
CC
(1)
CC
CC
CC
= 2V
= 3V
= 5V
CC
CC
(Continued)
CC
= 2V
= 3V
= 5V
values.
= 3V
= 3V
Figure
Min.
30
20
22-23,
(2)
CC
CC
= 5V, 5 mA at V
Figure
= 5V, 5 mA at V
Typ.
0.35
0.3
1.5
0.1
1.2
22-24,
5
Figure
ATtiny25/45/85
CC
CC
= 3V) under steady state
Max.
= 3V) under steady state
0.55
22-25, and
2.5
0.2
0.6
60
50
10
2
8
2
(3)
Figure 22-26
Units
mA
mA
mA
mA
mA
mA
µA
µA
167

Related parts for attiny25v