xr17l152im Exar Corporation, xr17l152im Datasheet - Page 31
![no-image](/images/manufacturer_photos/0/2/243/exar_corporation_sml.jpg)
xr17l152im
Manufacturer Part Number
xr17l152im
Description
3.3v Pci Bus Dual Uart
Manufacturer
Exar Corporation
Datasheet
1.XR17L152IM.pdf
(55 pages)
XR17L152
3.3V PCI BUS DUAL UART
REV. 1.1.0
Baud Rate Generator Divisors (DLL and DLM)
The Baud Rate Generator (BRG) is a 16-bit counter that generates the data rate for the transmitter and
receiver. The rate is programmed through registers DLL and DLM which are only accessible when LCR bit-7 is
set to logic 1. See Programmable Baud Rate Generator section for more detail.
Interrupt Enable Register (IER)
The Interrupt Enable Register (IER) masks the interrupts from receive data ready, transmit empty, line status
and modem status registers. These interrupts are reported in the Interrupt Status Register (ISR) register and
also encoded in INT (INT0-INT3) register in the Device Configuration Registers.
IER versus Receive FIFO Interrupt Mode Operation
When the receive FIFO (FCR BIT-0 = logic 1) and receive interrupts (IER BIT-0 = logic 1) are enabled, the RHR
interrupts (see ISR bits 3 and 4) status will reflect the following:
A. The receive data available interrupts are issued to the host when the FIFO has reached the programmed
B. FIFO level will be reflected in the ISR register when the FIFO trigger level is reached. Both the ISR register
C. The receive data ready bit (LSR BIT-0) is set as soon as a character is transferred from the shift register to
IER versus Receive/Transmit FIFO Polled Mode Operation
When FCR BIT-0 equals a logic 1 for FIFO enable; resetting IER bits 0-3 enables the L152 in the FIFO polled
mode of operation. Since the receiver and transmitter have separate bits in the LSR either or both can be used
in the polled mode by selecting respective transmit or receive control bit(s).
A. LSR BIT-0 indicates there is data in RHR or RX FIFO.
B. LSR BIT 1-4 provides the type of receive data errors encountered for the data byte in RHR, if any.
C. LSR BIT-5 indicates THR is empty.
D. LSR BIT-6 indicates when both the transmit FIFO and TSR are empty.
E. LSR BIT-7 indicates a data error in at least one character in the RX FIFO.
IER[0]: RHR Interrupt Enable
The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when
the receive FIFO has reached the programmed trigger level in the FIFO mode.
IER[1]: THR Interrupt Enable
This interrupt is associated with bit-5 in the LSR register. An interrupt is issued whenever the THR becomes
empty (non-FIFO mode) or when data in the FIFO falls below the programmed trigger level in the 64-byte FIFO
mode.
IER[2]: Receive Line Status Interrupt Enable
If any of the LSR register bits 1, 2, 3 or 4 is a logic 1, it will generate an interrupt to inform the host controller
about the error status of the current data byte in FIFO. An interrupt is generated immediately when a character
with an error has been received.
Logic 0 = Disable the receive data ready interrupt (default).
Logic 1 = Enable the receiver data ready interrupt.
Logic 0 = Disable Transmit Holding Register empty interrupt (default).
Logic 1 = Enable Transmit Holding Register empty interrupt.
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
trigger level. It will be cleared when the FIFO drops below the programmed trigger level.
status bit and the interrupt will be cleared when the FIFO drops below the trigger level.
the receive FIFO. It is reset when the FIFO is empty.
31
DISCONTINUED
áç
áç
áç
áç