sc16c652-04 NXP Semiconductors, sc16c652-04 Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
sc16c652-04
Manufacturer Part Number
sc16c652-04
Description
Sc16c652 Dual Uart With 32 Bytes Of Transmit And Receive Fifos
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C652-04.pdf
(41 pages)
Philips Semiconductors
9397 750 11634
Product data
7.3.2 FIFO mode
Table 11:
Bit
7-6
5-4
3
2
Symbol
FCR[7]
(MSB),
FCR[6]
(LSB)
FCR[5]
(MSB),
FCR[4]
(LSB)
FCR[3]
FCR[2]
FIFO Control Register bits description
Rev. 04 — 20 June 2003
Description
RCVR trigger. These bits are used to set the trigger level for the receive
FIFO interrupt.
An interrupt is generated when the number of characters in the FIFO
equals the programmed trigger level. However, the FIFO will continue to
be loaded until it is full. Refer to
Logic 0 or cleared is the default condition; TX trigger level = 16.
These bits are used to set the trigger level for the transmit FIFO
interrupt. The SC16C652 will issue a transmit empty interrupt when the
number of characters in FIFO drops below the selected trigger level.
Refer to
DMA mode select.
Transmit operation in mode ‘0’: When the SC16C652 is in the 16C450
mode (FIFOs disabled; FCR[0] = logic 0) or in the FIFO mode (FIFOs
enabled; FCR[0] = logic 1; FCR[3] = logic 0), and when there are no
characters in the transmit FIFO or transmit holding register, the TXRDY
pin will be a logic 0. Once active, the TXRDY pin will go to a logic 1 after
the first character is loaded into the transmit holding register.
Receive operation in mode ‘0’: When the SC16C652 is in 16C450
mode, or in the FIFO mode (FCR[0] = logic 1; FCR[3] = logic 0) and
there is at least one character in the receive FIFO, the RXRDY pin will
be a logic 0. Once active, the RXRDY pin will go to a logic 1 when there
are no more characters in the receiver.
Transmit operation in mode ‘1’: When the SC16C652 is in FIFO mode
(FCR[0] = logic 1; FCR[3] = logic 1), the TXRDY pin will be a logic 1
when the transmit FIFO is completely full. It will be a logic 0 when the
trigger level has been reached.
Receive operation in mode ‘1’: When the SC16C652 is in FIFO mode
(FCR[0] = logic 1; FCR[3] = logic 1) and the trigger level has been
reached, or a Receive Time-Out has occurred, the RXRDY pin will go to
a logic 0. Once activated, it will go to a logic 1 after there are no more
characters in the FIFO.
XMIT FIFO reset.
Logic 0 = Set DMA mode ‘0’ (normal default condition).
Logic 1 = Set DMA mode ‘1’
Logic 0 = No FIFO transmit reset (normal default condition).
Logic 1 = Clears the contents of the transmit FIFO and resets the
FIFO counter logic (the transmit shift register is not cleared or
altered). This bit will return to a logic 0 after clearing the FIFO.
Dual UART with 32 bytes of transmit and receive FIFOs
Table
13.
Table
12.
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
SC16C652
18 of 41