sc16c652 NXP Semiconductors, sc16c652 Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
sc16c652
Manufacturer Part Number
sc16c652
Description
Dual Uart With 32 Bytes Of Transmit And Receive Fifos
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C652.pdf
(41 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
sc16c652B
Manufacturer:
PHILIPS
Quantity:
42
Company:
Part Number:
sc16c652BIB48
Manufacturer:
AD
Quantity:
9 600
Part Number:
sc16c652BIB48
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Company:
Part Number:
sc16c652BIB48,128
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
sc16c652BIB48,151
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
sc16c652BIB48,157
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
sc16c652IB48
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Company:
Part Number:
sc16c652IB48,128
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
Table 2:
9397 750 11634
Product data
Symbol
INTA, INTB
IOR
IOW
OP2A,
OP2B
RESET
RXRDYA,
RXRDYB
TXRDYA,
TXRDYB
V
XTAL1
XTAL2
CDA, CDB
CC
Pin description
30, 29
19
15
32, 9
36
31, 18
43, 6
42
13
14
40, 16
LQFP48
Pin
Type
O
I
I
O
I
O
O
I
I
O
I
…continued
Description
Interrupt A, B (3-State). This function is associated with individual channel interrupts,
INTA, INTB. INTA, INTB are enabled when MCR bit 3 is set to a logic 1, interrupts are
enabled in the interrupt enable register (IER), and is active when an interrupt condition
exists. Interrupt conditions include: receiver errors, available receiver buffer data, transmit
buffer empty, or when a modem status flag is detected.
Read strobe (Active-LOW strobe). A logic 0 transition on this pin will load the contents
of an internal register defined by address bits A0-A2 onto the SC16C652 data bus
(D0-D7) for access by external CPU.
Write strobe (Active-LOW strobe). A logic 0 transition on this pin will transfer the
contents of the data bus (D0-D7) from the external CPU to an internal register that is
defined by address bits A0-A2.
Output 2 (user-defined). This function is associated with individual channels, A through
B. The state at these pin(s) are defined by the user and through MCR register bit 3. INTA,
INTB are set to the active mode and OP2 to logic 0 when MCR[3] is set to a logic 1. INTA,
INTB are set to the 3-State mode and OP2 to a logic 1 when MCR[3] is set to a logic 0.
See bit 3, Modem Control Register (MCR[3]). Since these bits control both the INTA,
INTB operation and OP2 outputs, only one function should be used at one time, INT or
OP2.
Reset (Active-HIGH). A logic 1 on this pin will reset the internal registers and all the
outputs. The UART transmitter output and the receiver input will be disabled during reset
time. (See
Receive Ready A, B (Active-LOW). This function provides the RX FIFO/RHR status for
individual receive channels (A-B). RXRDYn is primarily intended for monitoring DMA
mode 1 transfers for the receive data FIFOs. A logic 0 indicates there is a receive data to
read/upload, i.e., receive ready status with one or more RX characters available in the
FIFO/RHR. This pin is a logic 1 when the FIFO/RHR is empty or when the programmed
trigger level has not been reached. This signal can also be used for single mode transfers
(DMA mode 0).
Transmit Ready A, B (Active-LOW). These outputs provide the TX FIFO/THR status for
individual transmit channels (A-B). TXRDYn is primarily intended for monitoring DMA
mode 1 transfers for the transmit data FIFOs. An individual channel’s TXRDYA, TXRDYB
buffer ready status is indicated by logic 0, i.e., at lease one location is empty and
available in the FIFO or THR. This pin goes to a logic 1 (DMA mode 1) when there are no
more empty locations in the FIFO or THR. This signal can also be used for single mode
transfers (DMA mode 0).
Power supply input.
Crystal or external clock input. Functions as a crystal input or as an external clock
input. A crystal can be connected between this pin and XTAL2 to form an internal
oscillator circuit. This configuration requires an external 1 M resistor between the
XTAL1 and XTAL2 pins. Alternatively, an external clock can be connected to this pin to
provide custom data rates. (See
See
Output of the crystal oscillator or buffered clock. (See also XTAL1.) Crystal oscillator
output or buffered clock output. Should be left open if an external clock is connected to
XTAL1. For extended frequency operation, this pin should be tied to V
resistor.
Carrier Detect (Active-LOW). These inputs are associated with individual UART
channels A through B. A logic 0 on this pin indicates that a carrier has been detected by
the modem for that channel.
Figure
Section 7.11 “SC16C652 external reset condition”
3.
Rev. 04 — 20 June 2003
Dual UART with 32 bytes of transmit and receive FIFOs
Section 6.8 “Programmable baud rate
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
for initialization details.)
SC16C652
CC
generator”.)
via a 2 k
5 of 41