hsp50214 Intersil Corporation, hsp50214 Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
hsp50214
Manufacturer Part Number
hsp50214
Description
Programmable Downconverter
Manufacturer
Intersil Corporation
Datasheet
1.HSP50214.pdf
(54 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
hsp50214BVCZ
Manufacturer:
AD
Quantity:
1 001
Company:
Part Number:
hsp50214BVIZ
Manufacturer:
HONGFA
Quantity:
30 000
Part Number:
hsp50214BVIZ
Manufacturer:
INTERSIL
Quantity:
20 000
Pin Descriptions
GAINADJ(2:0)
AGCGNSEL
AOUT(15:0)
BOUT(15:0)
PROCCLK
COFSYNC
SOFSYNC
IN(13:0)
NAME
CLKIN
GND
COF
V
SOF
ENI
CC
TYPE
O
O
-
-
I
I
I
I
I
I
I
I
I
I
Positive Power Supply Voltage.
Ground.
Input Clock. This clock should be a multiple of the input sample rate. All input section processing oc-
curs on the rising edge of CLKIN.
Input Data. The format of the input data may be set to offset binary or 2’s complement. IN13 is the
MSB (see control word 0).
Input Enable. Active Low. This pin enables the input to the part in one of two modes, gated or inter-
polated (see control word 0). In gated mode, one sample is taken per CLKIN when ENI is asserted.
GAINADJ Input. Adds an offset to the gain via the shifter following the mixer. GAINADJ value is added
to the shift code from the microprocessor ( P) interface. The shift code is saturated to a maximum
code of F. The gain is offset by (6dB)(GAINADJ). (000 = 0dB gain adjust; 111 = 42dB gain adjust)
GAINADJ2 is the MSB. See “Using the Input Gain Adjust Control Signals” section.
Processing Clock. PROCCLK is the clock for all processing functions following the CIC section. Pro-
cessing is performed on PROCCLK’s rising edge. All output timing is derived from this clock.
NOTE: This clock may be asynchronous to CLKIN.
AGC Gain Select. This pin selects between two AGC loop gains. This input is setup and held relative
to PROCCLK. Gain setting 1 is selected when AGCGNSEL = 1.
Carrier Offset Frequency Input. This serial input pin is used to load the carrier offset frequency into the
Carrier NCO (see Serial Interface Section). The offset may be 8, 16, 24, or 32 bits. The setup and hold
times are relative to CLKIN. This input is compatible with the output of the HSP50210 Costas loop [1].
Carrier Offset Frequency Sync. This signal is asserted one CLK before the most significant bit (MSB)
of the offset frequency word (see Serial Interface Section). The setup and hold times are relative to
CLKIN. This input is compatible with the output of the HSP50210 Costas loop [1].
Resampler Offset Frequency Input. This serial input pin is used to load the offset frequency into the
Resampler NCO (see Serial Interface Section). The offset may be 8, 16, 24, or 32 bits. The setup and
hold times are relative to PROCCLK. This input is compatible with the output of the HSP50210 Costas
loop [1].
Resampler Offset Frequency Sync. This signal is asserted one CLK before the MSB of the offset fre-
quency word (see Serial Interface Section). The setup and hold times are relative to PROCCLK. This
input is compatible with the output of the HSP50210 Costas loop [1].
Parallel Output Bus A. Two parallel output sources are available on the HSP50214. The first is called
the Direct Output Port, where the source is selected through control word 20 (see the Microprocessor
Write section) and comes directly from the Output MUX section (see Output Control Section). The
most significant byte of AOUT always outputs the most significant byte of the Parallel Direct Output
Port whose format is selected via P interface. AOUT15 is the MSB. In this mode, the AOUT(15:0)
bus is updated as soon as data is available. DATARDY is asserted to indicate new data.
The second source for parallel data is called the Buffer RAM Output Port. The Buffer RAM Output
Port acts like a FIFO for blocks of information called data sets. Within a data set is I, Q, magnitude,
phase, and frequency information; a data type is selected using SEL(2:0). Up to 7 data sets are stored
in the Buffer RAM Output Port. The LSBytes of the AOUT and BOUT busses form the 16 bits for the
buffered output mode and can be used for buffered mode while the MSBytes are outputting data in
the direct output mode.
Parallel Output Bus B. Two parallel output sources are available on the HSP50214. The first is called
the Direct Output Port, where the source is selected through control word 20 (see the Microprocessor
Write section) and comes directly from the Output MUX section (see Output Control Section). The
most significant byte of BOUT always outputs the most significant byte of the Parallel Direct Output
Port whose format is selected via P interface. BOUT15 is the MSB. In this mode, the BOUT(15:0)
bus is updated as soon as data is available. DATARDY is asserted to indicate new data.
The second source for parallel data is called the Buffer RAM Output Port. The Buffer RAM Output
Port acts like a FIFO for blocks of information called data sets. Within a data set is I, Q, magnitude,
phase, and frequency information; a particular information is selected using SEL(2:0). Up to 7 data
sets is stored in the Buffer RAM Output Port. The least significant byte of BOUT can be used to either
output the least significant byte of the B Parallel Direct Output Port or the least significant byte of the
Buffer RAM Output Port. See Output Section.
HSP50214
3
DESCRIPTION