am79c30a Advanced Micro Devices, am79c30a Datasheet - Page 48
![no-image](/images/manufacturer_photos/0/0/14/advanced_micro_devices_sml.jpg)
am79c30a
Manufacturer Part Number
am79c30a
Description
Digital Subscriber Controller ?dsc ?circuit
Manufacturer
Advanced Micro Devices
Datasheet
1.AM79C30A.pdf
(101 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
am79c30a-JC
Manufacturer:
SPW
Quantity:
4 480
Company:
Part Number:
am79c30aJC
Manufacturer:
AMD
Quantity:
3 041
Company:
Part Number:
am79c30aJC/C
Manufacturer:
AMD
Quantity:
5 530
Company:
Part Number:
am79c30aJC/C
Manufacturer:
AMD
Quantity:
5 530
Company:
Part Number:
am79c30aJC/C
Manufacturer:
NS
Quantity:
5 120
Peripheral Port (PP)
Overview
The purpose of the Peripheral Port is to allow external
peripherals to be connected to the DSC/IDC circuit.
There are two basic modes of operation, Serial Bus
Port mode, and IOM-2 Terminal mode. Within IOM-2
Terminal mode, the DSC/IDC circuit may be configured
as any combination of IOM-2 timing/control master or
slave. The definition of the Peripheral Port pins de-
pends on the operating mode of the port, as described
in Table 50.
Serial Bus Port (SBP) Mode
The SBP mode of operation is backwards compatible
with the Revision D DSC circuit serial port and is en-
tered either following a device RESET or if pro-
grammed in PPCR1.
In SBP mode, the SCLK output provides a 192-kHz 1X
data clock of programmable polarity. The SBIN and
SBOUT pins support three 8-bit serial data channels,
designated Bd, Be, and Bf. The SFS output provides an
8-kHz serial frame sync pulse eight bit periods in width,
coincident with the Bd channel. The SBP mode timing
is illustrated in Figure 5.
48
SBIN
SBOUT
SCLK
SFS
BCL/CH2STRB
IN = Input
Note:
*The Am79C30A is a non-Layer-1 component when operated in the Slave mode; however, it has a microprocessor interface.
As a result, it is required to change the direction of its I/O pins at certain times in order to communicate with both the upstream
Layer-1 device and any downstream peripheral devices. In the IOM-2 Slave mode, the direction of data flow is reversed with
respect to the DSC circuit during Sub-frame 0 and during the deactivated state. The rule is that the upstream Layer-1 device
only uses Sub-frame 0 and does not reverse its pins. Any non-Layer-1 component that does not contain a microprocessor
interface (i.e., program by the DSC circuit over the Monitor channel in Sub-frame 1) uses Sub-frame 0 to talk to the Layer-1
device and Sub-frame 1 to talk to the DSC circuit. It does not reverse its pins.
Pin
SBP
On
IN
OUT
OUT
OUT
OUT
OUT = Output
Port
Disabled
Z
Z
Z
Z
Z
Table 50. Pin Operation versus Peripheral Port Modes
IOM-2 M
Activated
IN
OD
OUT
OUT
OUT
Z = High Impedance
Am79C30A/32A Data Sheet
IOM-2 M
Deactivated
IN
Z
Low
Low
Low
IOM-2 S*
Bus Reverse
Activated
IN/OD
OD/IN
IN
IN
Z
Following a RESET, the SCLK and SFS outputs will de-
fault to a high-impedance state, which will be main-
tained until any MUX connection is programmed (or
until the Peripheral Port is programmed to an IOM-2
mode). SCLK and SFS will remain in a high-impedance
state if the Peripheral Port is explicitly disabled. The
SCLK and SFS signals are synchronized to the re-
ceived S-interface frame. If there is no S-interface
frame synchronization, the SCLK and SFS signals will
free-run at 192 kHz and 8 kHz respectively.
If the DSC/IDC circuit is programmed to Idle mode, the
SFS output is driven Low but SCLK continues to run. In
Power-Down mode, both the SFS and SCLK outputs
are high-impedance.
IOM-2 Terminal Mode Overview
The IOM-2 Interface standard encompasses both a Li-
necard mode and a Terminal mode. The Terminal
mode was defined to provide four functions, as follows:
1. Connection of multiple Layer-2 devices to a Layer-1
2. Programming and control of Layer-1 or Layer-2 de-
device (in this case, the Layer-1 device is the S/T In-
terface LIU). Provision for the connection of
non-IOM-2 devices is included.
vices that do not have a microprocessor interface,
for example, a U-interface transceiver.
OD = Open Drain Output
IOM-2 S* Bus
Reverse
Deactivated
OD
Z
IN
IN
Z
IOM-2 S No
Bus Reverse
Activated
OD
IN
IN
IN
Z
IOM-2 S No
Bus Reverse
Deactivated
Z
IN
IN
Z
Z