am79c30a Advanced Micro Devices, am79c30a Datasheet - Page 64
![no-image](/images/manufacturer_photos/0/0/14/advanced_micro_devices_sml.jpg)
am79c30a
Manufacturer Part Number
am79c30a
Description
Digital Subscriber Controller ?dsc ?circuit
Manufacturer
Advanced Micro Devices
Datasheet
1.AM79C30A.pdf
(101 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
am79c30a-JC
Manufacturer:
SPW
Quantity:
4 480
Company:
Part Number:
am79c30aJC
Manufacturer:
AMD
Quantity:
3 041
Company:
Part Number:
am79c30aJC/C
Manufacturer:
AMD
Quantity:
5 530
Company:
Part Number:
am79c30aJC/C
Manufacturer:
AMD
Quantity:
5 530
Company:
Part Number:
am79c30aJC/C
Manufacturer:
NS
Quantity:
5 120
Peripheral Port Control Register 2 (PPCR2)
Default = Bits 7, 6, and 0 = 0, Bit 5 = 1, Bits 4–1 are Indeterminate*
Address = Indirect C8 Hex, Read/Write
The Peripheral Port Control Register 2 controls the inversion of the SCLK output in SBP mode. This provides flexi-
bility in the connection of peripheral devices to the DSC circuit. The hardware revision code is also contained in this
register, which allows software to identify the revision of the hardware.
Note:
* The default value is revision-level dependent. Revision J will report a hardware revision code of 110.
Peripheral Port Control Register 3 (PPCR3)
Default = Bits 7–5 are Indeterminate, Bit 4=1, Bit 3=0, Bits 2-0= 1
Address = Indirect C9 Hex, Read/Write
64
Bit
7–5
0
Bit
7–5
4
3
2–0
Function
Hardware Revision Code—This read-only field reports the hardware revision level. Revision J of the DSC circuit will
report a hardware revision code of 110. The hardware revision codes for E and H are 100, 010, respectively.
SCLK Inversion Enable—When set, the SCLK output is inverted in SBP mode. When cleared, the SCLK output is
identical to the Revision D DSC circuit. This bit should not be changed while SCLK is enabled.
Function
RESERVED
SLAVE Mode Bus Reversal—PPCR3.4 controls the bus reversal function of the DSC’s IOM-2 SLAVE mode. By default
(PPCR3.4=1) the Slave bus reverses to ensure backwards compatibility with previous revisions. When PPCR3.4=0 the
IOM-2 bus will not reverse in SLAVE mode. This assures slave compatibility of the control function and allows use with
devices such as the ISAC-S.
TIC Bus Enable—PPCR3.3 controls enabling and disabling of TIC bus operation. When PPCR3.3=0 which is the default
condition, the IOM-2 bus will not support the TIC bus feature to ensure backwards compatibility with previous IOM-2
capable revisions of the 79C30A. The TIC bus control logic features are only enabled if PPCR3.3=1.
Features enabled when PPCR3.3=1
S/G bit
When the DSC is in IOM-2 MASTER mode the CTS output of the LIU is used to drive the transmitted S/G bit. This signal
indicates D-channel Clear To Send status and is set when the LIU collision detection logic fulfills the programmed priority
level requirements.
When in IOM-2 SLAVE mode the received S/G bit is used as the Clear To Send input into the DLC block.
TIC Address Bus and Bus Accessed
Refer to TIC bus operation section.
TIC Bus Address—Device address to be used on TIC bus. Default is 111.
CODE
(MSB)
BIT 2
REV
7
CODE
BIT 1
REV
6
CODE
(LSB)
BIT 0
REV
5
Am79C30A/32A Data Sheet
RSRVD
4
RSRVD
3
RSRVD
2
RSRVD
1
ENABL
INVRT
SCLK
0