oq2541u NXP Semiconductors, oq2541u Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
oq2541u
Manufacturer Part Number
oq2541u
Description
Sdh/sonet Data And Clock Recovery Unit Stm1/4/16 Oc3/12/48 Ge
Manufacturer
NXP Semiconductors
Datasheet
1.OQ2541U.pdf
(36 pages)
Philips Semiconductors
Reference frequency select
A reference clock signal of 19.44 or 38.88 MHz must be
connected to pins CREF and CREFQ. It should be noted
that the reference frequency should be either
39.0625 MHz or 19.53125 MHz in a Gigabit Ethernet
system. Pins DREF19 and DREF39 are used to select the
appropriate output frequency at frequency divider 2
(see Table 2).
To minimize the adverse influence of reference clock
crosstalk, a differential signal with an amplitude from
75 to 150 mV (p-p) is advised.
Since the reference clock is only used as an acquisition aid
for the PLL of the frequency window detector, the quality
of the reference clock (i.e. phase noise) is not important.
There is no phase noise specification imposed on the
reference clock generator and even frequency stability
may be in the order of 100 ppm. In general, most
inexpensive crystal based oscillators are suitable.
When the OQ2541 is used in an application with a fixed
reference clock frequency, it is best to connect the planes
of pins DREF19 and DREF39 with a short trace or a via to
the plane of pin GND or pin V
clock frequency is required in the application, the pins can
be controlled through low ohmic switching FETs,
e.g. BSH103 or equivalent (low R
Table 2 Reference frequency selection
STM mode selection
The VCRO has a very large tuning range. However, the
performance of the OQ2541 is optimized for SDH/SONET
bit rates.
Table 3 STM mode select
1999 May 27
FREQUENC
STM1/OC3
STM4/OC12
Gigabit Ethernet
STM16/OC48
SDH/SONET data and clock recovery unit
STM1/4/16 OC3/12/48 GE
Y (MHz)
38.88
19.44
MODE
DIVISION
FACTOR
128
64
BIT RATE
(Mbits/s)
1250.00
2488.32
155.52
622.08
EE
. If a selectable reference
DREF19
ground
DSon
V
LEVEL ON PIN
EE
).
DIVISION
FACTOR
DREF39
16
V
V
4
2
1
EE
EE
10
Due to the nature of the PLL, the very wide tuning range is
a necessity for proper lock behaviour over the guaranteed
temperature range, aging and batch to batch spread.
Though it might seem that the OQ2541 is capable of
recovering other bit rates than SDH/SONET and Gigabit
Ethernet rates (STM1/OC3, STM4/OC12, STM16/OC48
and 1250 Mbits/s), the behaviour can not be guaranteed.
The required SDH/SONET bit rate is selected by
connecting pins DOUT155, DOUT622 and DOUT1250
to ground or to the supply voltage V
The connections to V
milliamperes and should have low resistance and
inductance, so short printed-circuit board tracks are
recommended. In some cases a decoupling capacitor near
the selection pins can be necessary to provide a clean
return path for RF signals.
When the OQ2541 is used in an application with a fixed
data rate, it is best to connect the planes of
pins DOUT155, DOUT622 and DOUT1250 with a short
trace or a via to the plane of pin GND or pin V
selectable reference clock frequency is required in the
application, the pins can be controlled through low-ohmic
switching FETs, e.g. BSH103 or equivalent (low R
For STM16/OC48 (2488.32 Mbits/s) operation:
all three pins must be connected to ground
For Gigabit Ethernet (1250 Mbits/s) operation:
pin DOUT1250 must be connected to V
For STM4/OC12 (622.08 Mbits/s) operation:
pins DOUT1250 and DOUT622 must be connected to
V
For STM1/OC3 (155,52 Mbits/s) operation:
all three pins must be connected to V
DOUT155
EE
ground
ground
ground
V
(the dividers are daisy chained)
EE
LEVEL ON PIN
OQ2541HP; OQ2541U
EE
DOUT622
and ground carry a current of a few
ground
ground
V
V
EE
EE
EE
Product specification
(see Table 3):
EE
EE
.
DOUT1250
ground
EE
V
V
V
EE
EE
EE
. If a
DSon
).