lxt9785 Intel Corporation, lxt9785 Datasheet - Page 147
![no-image](/images/manufacturer_photos/0/3/337/intel_corporation_sml.jpg)
lxt9785
Manufacturer Part Number
lxt9785
Description
Advanced 8-port 10/100 Mbps Phy Transceivers
Manufacturer
Intel Corporation
Datasheet
1.LXT9785.pdf
(226 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lxt9785EHC DO
Manufacturer:
INTEL
Quantity:
20 000
Part Number:
lxt9785HC
Manufacturer:
LEVELONE
Quantity:
20 000
Part Number:
lxt9785HC C2
Manufacturer:
INTEL
Quantity:
20 000
Company:
Part Number:
lxt9785HCB2
Manufacturer:
Intel
Quantity:
184
4.9.3.6
4.9.3.7
Datasheet
Document Number: 249241
Revision Number: 007
Revision Date: August 28, 2003
Note: The BGA15 package does not support fiber interface.
Twisted-Pair PMD Sublayer
The twisted-pair Physical Medium Dependent (PMD) layer provides the signal scrambling and
descrambling, line coding and decoding (MLT-3 for 100BASE-TX, Manchester for 10T), as well
as receiving, polarity correction, and baseline wander correction functions.
4.9.3.6.1 Scrambler/Descrambler (100BASE-TX Only)
The purpose of the scrambler is to spread the signal power spectrum and further reduce EMI using
an 11-bit, non-data-dependent polynomial. The receiver automatically decodes the polynomial
whenever IDLE symbols are received.
The scrambler/descrambler can be bypassed by setting Register bit 16.12 = 1. The scrambler is
automatically bypassed when the fiber port is enabled. Scrambler bypass is provided for diagnostic
and test support.
4.9.3.6.2 Baseline Wander Correction
The LXT9785/LXT9785E provides a baseline wander correction function which makes the device
robust under all network operating conditions. The MLT3 coding scheme used in 100BASE-TX is,
by definition, “unbalanced”. This means that the DC average value of the signal voltage can
“wander” significantly over short time intervals (tenths of seconds). This wander may cause
receiver errors, particularly in less robust designs, at long line lengths (100 meters). The exact
characteristics of the wander are completely data dependent.
The LXT9785/LXT9785E baseline wander correction characteristics allow the device to recover
error-free data while receiving worst-case “killer” packets over all cable lengths.
4.9.3.6.3 Polarity Correction
The LXT9785/LXT9785E automatically detects and corrects for the condition where the receive
signal (TPFIP/N) is inverted. Reversed polarity is detected if eight inverted link pulses or four
inverted End-of-Frame (EOF) markers are received consecutively. If link pulses or data are not
received by the maximum receive time-out period, the polarity state is reset to a non-inverted state.
Before the polarity switch occurs, every frame is inverted and causes RxER to assert. The specific
number of RxER events observed depends on how many link pulses occur between packets.
Fiber PMD Sublayer
The LXT9785/LXT9785E provides an LVPECL interface for connection to an external 3.3 V or
5 V fiber-optic transceiver. (The external transceiver provides the PMD function for the optical
medium.) The LXT9785/LXT9785E uses a 125 Mbaud NRZI format for the fiber interface, and
does not support 10BASE-FL applications.
4.9.3.7.1 Far End Fault Indications
The LXT9785/LXT9785E Signal Detect pins independently detect signal faults from the local
fiber transceivers via the SD pins. The device also uses Register bit 1.4 to report Remote Fault
indications received from its link partner. The device “ORs” both fault conditions to set bit 1.4.
Register bit 1.4 is set once and clears when read.
LXT9785 and LXT9785E Advanced 8-Port 10/100 Mbps PHY Transceivers
149