lxt9785 Intel Corporation, lxt9785 Datasheet - Page 198
![no-image](/images/manufacturer_photos/0/3/337/intel_corporation_sml.jpg)
lxt9785
Manufacturer Part Number
lxt9785
Description
Advanced 8-port 10/100 Mbps Phy Transceivers
Manufacturer
Intel Corporation
Datasheet
1.LXT9785.pdf
(226 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lxt9785EHC DO
Manufacturer:
INTEL
Quantity:
20 000
Part Number:
lxt9785HC
Manufacturer:
LEVELONE
Quantity:
20 000
Part Number:
lxt9785HC C2
Manufacturer:
INTEL
Quantity:
20 000
Company:
Part Number:
lxt9785HCB2
Manufacturer:
Intel
Quantity:
184
LXT9785 and LXT9785E Advanced 8-Port 10/100 Mbps PHY Transceivers
200
Table 82. Intel
Table 83. Control Register (Address 0) (Sheet 1 of 2)
Address
1. R/W = Read/Write, SC = Self Clearing when operation complete.
2. During a hardware reset, all LHR information is latched in from the pins. During a software reset (0.15), the
3. LSHR = Default value is derived from a single device input pin state or a group of device input pin states as
4. Default value of Register bits 0.12, 0.13, and 0.8 are determined by the CFG pins as described in
5. Default value of Register bit 0.11 is determined by the LINKHOLD configuration pin.
30 - 31
Bit
15
14
13
12
10
11
9
8
LSHR information is not re-read from the pins. This information reverts back to the information that was
read in during the hardware reset. During a hardware rest, register information is unavailable from 1 ms
after de-assertion of the reset. During a software reset (0.15) the registers are available for reading. The
reset bit should be polled to see when the part has completed reset.
the pin(s) are latched at startup or hardware reset.
“Intel® LXT9785/9785E Global Hardware Configuration Settings” on page
27
28
29
®
LXT9785/LXT9785E Register Set (Sheet 2 of 2)
Name
RESET
Loopback
Speed Selection
Auto-Negotiation
Enable
Power-Down
Isolate
Restart
Auto-Negotiation
Duplex Mode
Register Name
“Trim Enable Register (Address 27, Hex 1B)”
Reserved
“Cable Diagnostics Register (Address 29, Hex 1D)”
Reserved
Description
0 = Normal operation
1 = PHY reset
0 = Disable loopback mode
1 = Enable loopback mode
Not recommended to enable auto-negotiation
while in internal loopback operation.
0 = Disable auto-negotiation process
1 = Enable auto-negotiation process
0 = Normal operation
1 = Power-down
0 = Normal operation
1 = Electrically isolate PHY from RMII/SMII/SS-
0 = Normal operation
1 = Restart auto-negotiation process
0 = Half-duplex
1 = Full-duplex
0.6
1
1
0
0
SMII interfaces
0.13
1 = Reserved
0 = 1000 Mbps (not allowed)
1 = 100 Mbps
0 = 10 Mbps
129.
Bit Assignments
Refer to
N/A
Refer to
N/A
Revision Date: August 28, 2003
Document Number: 249241
Table 99 on page 216
Table 100 on page 217
Type
Revision Number: 007
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
SC
SC
1
Datasheet
LSHR
LSHR
LSHR
LSHR
Table 42,
Default
0
0
0
0
2
3,4
3,4
3,5
3,4