TDA8360 PHILIPS [NXP Semiconductors], TDA8360 Datasheet
TDA8360
Related parts for TDA8360
TDA8360 Summary of contents
Page 1
... DATA SHEET TDA8360; TDA8361; TDA8362 Integrated PAL and PAL/NTSC TV processors Objective specification File under Integrated Circuits, IC02 Philips Semiconductors INTEGRATED CIRCUITS March 1994 ...
Page 2
... Because of the different functional contents of the ICs the set maker can make the optimum choice depending on the requirements for the receiver. The TDA8360 is intended for simple PAL receivers (all PAL standards, including PAL-N and PAL-M are possible). The TDA8361 contains a PAL/NTSC decoder and has an A/V switch ...
Page 3
... I horizontal output current 37 I vertical output current 43 Control voltages V control voltages for Volume, Contrast, control Saturation, Brightness, Hue and Peaking March 1994 TDA8360; TDA8361; TDA8362 CONDITIONS MIN. 7.2 TDA8361, TDA8362 TDA8361, TDA8362 Objective specification TYP. MAX. ...
Page 4
... Philips Semiconductors Integrated PAL and PAL/NTSC TV processors March 1994 TDA8360; TDA8361; TDA8362 4 Objective specification ...
Page 5
... Philips Semiconductors Integrated PAL and PAL/NTSC TV processors March 1994 TDA8360; TDA8361; TDA8362 5 Objective specification ...
Page 6
... Philips Semiconductors Integrated PAL and PAL/NTSC TV processors March 1994 TDA8360; TDA8361; TDA8362 6 Objective specification ...
Page 7
... BIN 29 RYI CON 25 28 BYI 26 SAT 27 HUE MBC203 Fig.4 Pin configuration for TDA8362. March 1994 TDA8360; TDA8361; TDA8362 SYMBOL PIN AUDEEM 1 audio de-emphasis and IFDEM1 2 IF demodulator tuned circuit IFDEM2 3 IF demodulator tuned circuit IDENT 4 video identification output/MUTE input SOIF ...
Page 8
... Therefore search tuning is possible when the display section of the receiver is used as a monitor. In the TDA8360 this circuit is only used for stable OSD at no signal input. In the normal television mode the identification output is connected to the coincidence detector, this applies to all three devices ...
Page 9
... The line oscillator operates at twice the line frequency. March 1994 TDA8360; TDA8361; TDA8362 The oscillator network is internal. Because of the spread of internal components an automatic adjustment circuit has been added to the IC. The circuit compares the oscillator frequency with that of the crystal oscillator in the colour decoder ...
Page 10
... TDA8361 This IC contains an automatic PAL/NTSC decoder. The conditions for connecting the reference crystals are the same as for the TDA8360. The decoder can be forced to PAL when the hue control pin is connected to the positive supply voltage via resistor (approximately) ...
Page 11
... March 1994 PARAMETER PARAMETER CONDITIONS note 1 including start supply 45 46) AND note 38.90 MHz 45.75 MHz 58.75 MHz i note 3 note 3 11 Objective specification TDA8360; TDA8361; TDA8362 MIN. MAX. 9.0 25 +150 25 +70 260 150 THERMAL RESISTANCE 40 K/W MIN. TYP. MAX. 7.2 8.0 8.8 80 6.5 0.7 70 100 70 ...
Page 12
... V = 0.92 or 1.1 MHz 0.92 or 1.1 MHz 2.66 or 3.3 MHz 2.66 or 3.3 MHz 60 o notes 7 and end of control range note 7 note 7 12 Objective specification TDA8360; TDA8361; TDA8362 MIN. TYP. MAX. 4.45 4.6 4.75 1.9 2 2.1 1.85 2 2.15 4.2 4 ...
Page 13
... March 1994 CONDITIONS 30% AM for 1 to 100 mV 200 Hz note 13 maximum gain minimum gain O(max) note 7 ( 8362 TDA NOTE PIN 13 Objective specification TDA8360; TDA8361; TDA8362 MIN. TYP. MAX 100 10 200 0.2 0.5 100 150 0.5 4 300 ...
Page 14
... MHz osc 5) note 17 note 3 note RMS; I note 18 note 17 50) 6 dB; note 17 note 19 note 7 note 7 see also Fig.5 note 20 14 Objective specification TDA8360; TDA8361; TDA8362 MIN. TYP. MAX. 0 4.2 6.8 100 350 15 3 500 700 ...
Page 15
... TDA NOTE PIN maximum volume ( 13 15) PINS AND notes 3 and 22 note 3 note 23 ( 8361, 8362; TDA TDA PIN notes 3 and 24 note 7 note 3 notes 7 and 23 15 Objective specification TDA8360; TDA8361; TDA8362 MIN. TYP. 350 700 2 1 16) 0 0 ...
Page 16
... March 1994 CONDITIONS ( 22, 23 24) PINS AND note 25 no data insertion data insertion data insertion note 23 note 23 note 26 note 29) PINS AND notes 7 and 27 note 7 16 Objective specification TDA8360; TDA8361; TDA8362 MIN. TYP. MAX. 0.7 0.8 1 100 0.1 0 1.05 1.35 0.1 1 ...
Page 17
... PINS AND referenced to pin 15; note 3 note 29 note 30 note 10%; P note amb note 7 40) FILTER CONNECTED TO PIN note 7 17 Objective specification TDA8360; TDA8361; TDA8362 MIN. TYP. MAX. 480 8 160 300 50 22 15625 2 0.2 0 0.9 1.2 ...
Page 18
... March 1994 CONDITIONS 39) CAPACITOR CONNECTED TO PIN without R L note 7 note note 7 ( 38) PIN note 7 note 33 42) note mode 18 Objective specification TDA8360; TDA8361; TDA8362 MIN. TYP. on pin 39 150 100 4.8 5.3 1.8 2.0 2.6 3.0 3.3 3.5 14 5.2 5.4 50/60 45 ...
Page 19
... ACL starts to operate R EFERENCE PART Phase-locked loop; note 37 f catching range CR phase shift for a 200 Hz deviation of the oscillator frequency March 1994 TDA8360; TDA8361; TDA8362 CONDITIONS MIN. note 2.0 note power note 36 26 ...
Page 20
... V residual carrier output voltage 30,31(p-p) (peak-to-peak value output (B Y) output V residual carrier output voltage 30,31(p-p) (peak-to-peak value output (B Y) output March 1994 TDA8360; TDA8361; TDA8362 CONDITIONS note 7 osc note 10 3.58 MHz; note 4.43 MHz; note 4 ...
Page 21
... TDA PIN note 41 PAL/NTSC identified no PAL/NTSC; SECAM (by TDA8395) identified 26) PIN see also Fig 10%;note colour identified note 37 21 Objective specification TDA8360; TDA8361; TDA8362 MIN. TYP. MAX. 25 0.1 0.1 5 0.51 10% 0.19 25% 1.12U 1.12V R R 0.20U + 1.12V R R ...
Page 22
... R Y signal (PAL) note 25 note 42 note 7 note 7 in the RGB note 23 osc plus osc nominal brightness note 7 note 7 22 Objective specification TDA8360; TDA8361; TDA8362 MIN. TYP. MAX. 20 0.7 1 3.5 4.0 4.5 3.8 4.2 4.6 0.5 0.6 0.8 1.2 1.3 1 150 1 ...
Page 23
... March 1994 CONDITIONS 20) nominal saturation; note 7 nominal contrast; note 7 nominal saturation nominal contrast nominal saturation nominal controls note 3.58 MHz osc f = 4.43 MHz osc 23 Objective specification TDA8360; TDA8361; TDA8362 MIN. TYP. MAX. 100 100 10 8 2.8 3.5 8 UNIT ...
Page 24
... This blanking overrules both the internal and external RGB signals. 27. The 3 dB bandwidth of the circuit can be calculated by means of the following equation – ------- - – osc 2Q March 1994 TDA8360; TDA8361; TDA8362 24 Objective specification ...
Page 25
... At a chrominance input voltage (related to CVBS2) of 660 mV (p-p) (colour bar with 75% saturation i.e. burst signal amplitude 300 mV (p-p)) the dynamic range of the ACC is +6 and 20 dB. March 1994 TDA8360; TDA8361; TDA8362 25 Objective specification ...
Page 26
... MHz the typical free running frequency is 15734. Calibration during start-up is always carried out with a 4.4 MHz crystal if no forced mode is used. March 1994 ( pF) = 4.433619 or 3.579545 MHz 20.6 fF (4.43 MHz crystal) or (3.58 MHz crystal account for parasitic capacitances Objective specification TDA8360; TDA8361; TDA8362 ...
Page 27
... No video identification QUALITY SPECIFICATION Quality level in accordance with UZW B0/FQ-0601. SYMBOL ESD protection circuit specification (note 1) Note 1. All pins are protected against ESD by means of internal clamping diodes. March 1994 TDA8360; TDA8361; TDA8362 EXTERNAL CHROMINANCE CVBS/Y OFF OFF ON ( (CVBS) ...
Page 28
... Fig.7 Hue control curve March 1994 MBC208 (%) (V) MBC206 - 1 (%) (V) 28 Objective specification TDA8360; TDA8361; TDA8362 Fig.6 Peaking control curve. 300 250 200 150 100 Fig.8 Saturation control curve. ...
Page 29
... Fig.9 Contrast control curve. MBC212 16 % for negative modulation 100% = 10% rest carrier Fig.11 Video output signal. March 1994 MBC205 (V) 100% 92% 30% 29 Objective specification TDA8360; TDA8361; TDA8362 1.0 ( Fig.10 Brightness control curve. MBC209 4 5 (V) ...
Page 30
... Fig.12 Test signal waveform. 3 BLUE PC ATTENUATOR CC at 3.58 or 4.4 MHz O 3 0.92 or 1.1 MHz O at 3.58 or 4.4 MHz O at 2.66 or 3.3 MHz O Fig.13 Test set-up intermodulation. 30 Objective specification TDA8360; TDA8361; TDA8362 100% 86% 72% 58% 44 MBC213 YELLOW TEST SPECTRUM CIRCUIT ...
Page 31
... The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified storage maximum. If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. March 1994 TDA8360; TDA8361; TDA8362 47.92 47.02 0.53 1.778 max (25x) 1 ...
Page 32
... Philips customers using or selling these products for use in such applications their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. March 1994 TDA8360; TDA8361; TDA8362 32 Objective specification ...
Page 33
... Philips Semiconductors Integrated PAL and PAL/NTSC TV processors March 1994 TDA8360; TDA8361; TDA8362 NOTES 33 Objective specification ...
Page 34
... Philips Semiconductors Integrated PAL and PAL/NTSC TV processors March 1994 TDA8360; TDA8361; TDA8362 NOTES 34 Objective specification ...
Page 35
... Philips Semiconductors Integrated PAL and PAL/NTSC TV processors March 1994 TDA8360; TDA8361; TDA8362 NOTES 35 Objective specification ...
Page 36
Philips Semiconductors – a worldwide company Argentina: IEROD, Av. Juramento 1992 - 14.b, (1428) BUENOS AIRES, Tel. (541)786 7633, Fax. (541)786 9367 Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. (02)805 4455, Fax. (02)805 4466 Austria: Triester Str. 64, ...