LAN9218I-MT-E2 SMSC [SMSC Corporation], LAN9218I-MT-E2 Datasheet - Page 79
LAN9218I-MT-E2
Manufacturer Part Number
LAN9218I-MT-E2
Description
High-Performance Single-Chip 10/100 Ethernet Controller with HP Auto-MDIX & Industrial Temperature Support
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.LAN9218I-MT-E2.pdf
(130 pages)
- Current page: 79 of 130
- Download datasheet (2Mb)
High-Performance Single-Chip 10/100 Ethernet Controller with HP Auto-MDIX & Industrial Temperature Support
Datasheet
SMSC LAN9218I
5.3.10
BITS
30-0
31
RX Data FIFO Fast Forward (RX_FFWD): Writing a ‘1’ to this bit causes
the RX data FIFO to fast-forward to the start of the next frame. This bit will
remain high until the RX data FIFO fast-forward operation has completed.
No reads should be issued to the RX data FIFO while this bit is high.
Note:
Reserved
In addition to the host-accessible FIFOs, the MAC Interface Layer (MIL) contains an additional 2K
bytes of TX, and 128 bytes of RX FIFO buffering. These sizes are fixed, and cannot be adjusted by
the host.
As space in the TX MIL (Mac Interface Layer) FIFO frees, data is moved into it from the TX data FIFO.
Depending on the size of the frames to be transmitted, the MIL can hold up to two Ethernet frames.
This is in addition to any TX data that may be queued in the TX data FIFO.
Conversely, as data is received by the LAN9218I, it is moved from the MAC to the RX MIL FIFO, and
then into the RX data FIFO. When the RX data FIFO fills up, data will continue to collect in the RX
MIL FIFO. If the RX MIL FIFO fills up and overruns, subsequent RX frames will be lost until room is
made in the RX data FIFO. For each frame of data that is lost, the RX Dropped Frames Counter
(RX_DROP) is incremented.
RX and TX MIL FIFO levels are not visible to the host processor. RX and TX MIL FIFOs operate
independent of the TX data and RX data and status FIFOs. FIFO levels set for the RX and TX data
and Status FIFOs do not take into consideration the MIL FIFOs.
RX_DP_CTRL—Receive Datapath Control Register
This register is used to discard unwanted receive frames.
Offset:
Please refer to section “Receive Data FIFO Fast Forward” on
page 52 for detailed information regarding the use of RX_FFWD.
DESCRIPTION
78h
DATASHEET
79
Size:
32 bits
TYPE
R/W
RO
Revision 1.5 (07-18-06)
DEFAULT
0h
-
Related parts for LAN9218I-MT-E2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: