FDC37C665GT_07 SMSC [SMSC Corporation], FDC37C665GT_07 Datasheet - Page 78
FDC37C665GT_07
Manufacturer Part Number
FDC37C665GT_07
Description
High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.FDC37C665GT_07.pdf
(152 pages)
- Current page: 78 of 152
- Download datasheet (435Kb)
The
incorporate two full function UARTs. They are
compatible with the NS16450, the 16450 ACE
registers and the NS16550A.
perform serial-to-parallel conversion on received
characters and parallel-to-serial conversion on
transmit characters.
independently programmable from 115.2K baud
down to 50 baud.
programmable for 1 start; 1, 1.5 or 2 stop bits;
even, odd, sticky or no parity; and prioritized
interrupts.
programmable baud rate generator that is
capable of dividing the input clock or crystal by
a number from 1 to 65535. The UARTs are also
capable of supporting the MIDI data rate. Refer
to the FDC37C665GT Configuration Registers
and the FDC37C666GT Hardware
*NOTE: DLAB is Bit 7 of the Line Control Register
FDC37C665GT
The UARTS each contain a
DLAB*
X
X
X
X
X
X
X
0
0
0
1
1
The character options are
The data rates are
and
A2
0
0
0
0
0
0
1
1
1
1
0
0
Table 34 - Addressing the Serial Port
FDC37C666GT
The UARTS
A1
0
0
0
1
1
1
0
0
1
1
0
0
SERIAL PORT (UART)
A0
0
0
1
0
0
1
0
1
0
1
0
1
78
Receive Buffer (read)
Transmit Buffer (write)
Interrupt Enable (read/write)
Interrupt Identification (read)
FIFO Control (write)
Line Control (read/write)
Modem Control (read/write)
Line Status (read/write)
Modem Status (read/write)
Scratchpad (read/write)
Divisor LSB (read/write)
Divisor MSB (read/write
Configuration description for information on
disabling, power down and changing the base
address of the UARTS. The interrupt from a
UART is enabled by programming OUT2 of that
UART to a logic "1". OUT2 being a logic "0"
disables that UART's interrupt.
REGISTER DESCRIPTION
Addressing of the accessible registers of the
Serial Port is shown below.
addresses of the serial ports are defined by the
configuration
section). The Serial Port registers are located at
sequentially increasing addresses above these
base addresses. The FDC37C665GT/666GT
contains two serial ports, each of which contain
a register set as described below.
REGISTER NAME
registers
(see
Configuration
The base
Related parts for FDC37C665GT_07
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: