MFRC52201HN1/TRAYB NXP [NXP Semiconductors], MFRC52201HN1/TRAYB Datasheet - Page 25
MFRC52201HN1/TRAYB
Manufacturer Part Number
MFRC52201HN1/TRAYB
Description
Contactless reader IC
Manufacturer
NXP [NXP Semiconductors]
Datasheet
1.MFRC52201HN1TRAYB.pdf
(96 pages)
- Current page: 25 of 96
- Download datasheet (527Kb)
NXP Semiconductors
MFRC522_33
Product data sheet
PUBLIC
8.2.3 Serial data switch
8.2.4 MFIN and MFOUT interface support
Two main blocks are implemented in the MFRC522. The digital block comprises the state
machines, encoder/decoder logic. The analog block comprises the modulator and
antenna drivers, the receiver and amplifiers. It is possible for the interface between these
two blocks to be configured so that the interfacing signals are routed to pins MFIN and
MFOUT.
This topology allows the analog block of the MFRC522 to be connected to the digital block
of another device.
The serial signal switch is controlled by the TxSelReg and RxSelReg registers.
Figure 20
The MFRC522 is divided into a digital circuit block and an analog circuit block. The digital
block contains state machines, encoder and decoder logic and so on. The analog block
contains the modulator and antenna drivers, receiver and amplifiers. The interface
between these two blocks can be configured so that the interfacing signals can be routed
to pins MFIN and MFOUT; see
using TxSelReg register’s MFOutSel[3:0] and DriverSel[1:0] bits and RxSelReg register’s
UARTSel[1:0] bits.
This topology allows some parts of the analog block to be connected to the digital block of
another device.
Switch MFOutSel in the TxSelReg register can be used to measure MIFARE and
ISO/IEC14443 A related signals. This is especially important during the design-in phase
or for test purposes as it enables checking of the transmitted and received data.
The most important use of pins MFIN and MFOUT is found in the active antenna concept.
An external active antenna circuit can be connected to the MFRC522’s digital block.
Switch MFOutSel must be configured so that the internal Miller encoded signal is sent to
pin MFOUT (MFOutSel = 100b). UARTSel[1:0] must be configured to receive a
Manchester signal with subcarrier from pin MFIN (UARTSel[1:0] = 01).
It is possible to connect a passive antenna to pins TX1, TX2 and RX (using the
appropriate filter and matching circuit) and an active antenna to pins MFOUT and MFIN at
the same time. In this configuration, two RF circuits can be driven (one after another) by a
single host processor.
Fig 20. Serial data switch for p-driver TX1 and TX2
shows the serial data switch for p-driver TX1 and TX2.
INTERNAL
CODER
MFIN
Rev. 3 — 26 October 2009
PolMFin = 0
InvMod = 1
INVERT IF
INVERT IF
112133
Figure 21 on page
envelope
3-state
1
DriverSel[1:0]
26. This configuration is implemented
00
01
10
11
to driver TX1 and TX2
0 = impedance = modulated
1 = impedance = CW
Contactless reader IC
MFRC522
© NXP B.V. 2009. All rights reserved.
001aak593
25 of 96
Related parts for MFRC52201HN1/TRAYB
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: