SAA6752HS/V103 PHILIPS [NXP Semiconductors], SAA6752HS/V103 Datasheet - Page 37

no-image

SAA6752HS/V103

Manufacturer Part Number
SAA6752HS/V103
Description
MPEG-2 video and MPEG-audio/AC-3 audio encoder with multiplexer
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SAA6752HS/V103
Manufacturer:
NXPLIPS
Quantity:
5 510
Part Number:
SAA6752HS/V103,557
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
Notes
1. ‘No copy’ flag is only detected if the correct WSS VBI mode is enabled.
2. This error flag detects mismatches between the input video format (525 or 625) and SAA6752HS video setting
3. A loss of video sync is flagged if 10 consecutive syncs are not detected.
4. For stream types which include video mode transitions to encode or idle/stop will not be finished, if no video is
5. In clock mode 1 and 3 this can occur due to discontinuity in the video input signal. In applications, which require an
7.12.3
A LOW level as signalled by the host interface pin
indicates that an exception condition has been detected.
The host interrupt flag pin H_IRF is reset to HIGH by
reading the interrupt status word via the I
7.12.4
It is possible to mask any combination of exception
conditions by setting a 16-bit interrupt mask via the
I
8
The SAA6752HS has built-in logic and 5 dedicated pins to
support boundary scan testing, which allows board testing
without special hardware (nails). The SAA6752HS follows
the “IEEE Std. 1149.1 - Standard Test Access Port and
Boundary Scan Architecture” set by the Joint Test Action
Group (JTAG) chaired by Philips.
The 5 special pins are: Test Mode Select (TMS), Test
Clock (TCK), Test Reset (TRST), Test Data Input (TDI)
and Test Data Output (TDO).
The Boundary Scan Test (BST) functions BYPASS,
EXTEST, SAMPLE, CLAMP and IDCODE are all
supported (see Table 12). Details on the JTAG BST-TEST
can be found in the specification “ IEEE Std. 1149.1” .
2004 Jan 26
2
WORD BIT
C-bus.
STATUS
MPEG-2 video and MPEG-audio/AC-3
audio encoder with multiplexer
(525 or 625). Video syncs out of range are also detected.
present. A pending mode transition can be stopped by forced reconfigure.
exact ratio between the number of generated audio frames and the number of generated video frames, the host might
start a corrective action. In clock mode 3 this exception can be ignored; it will happen after some encoding time,
because the audio processing is locked to the system frequency and video processing depends on the video input
frequency.
BOUNDARY SCAN TEST
13
14
15
H
I
NTERRUPT MASKING
OST INTERRUPT OPERATION
VBI WSS data has been captured
VBI CC data has been captured
memory manager resynchronization occurred
after discontinuity in the video input signal
EXCEPTION CONDITION
2
C-bus.
37
A file containing the detailed Boundary Scan Description
Language (BSDL) description of the SAA6752HS is
available on request.
8.1
The Test Access Port (TAP) controller of an IC should be
in the reset state (TEST_LOGIC_RESET), when the IC is
in functional mode. This reset state also forces the
instruction register into a functional instruction such as
IDCODE or BYPASS.
To solve the power-up reset, the standard specifies that
the TAP controller will be forced asynchronously to the
TEST_LOGIC_RESET state by setting pin TRST to LOW.
8.2
A device identification register is specified in “IEEE Std.
1149.1b-1994 ”. It is a 32-bit register which contains fields
for the specification of the IC manufacturer, the IC part
number and the IC version number. Its biggest advantage
is the possibility to check for the correct ICs mounted after
production and determination of the version number of ICs
during field service.
When the IDCODE instruction is loaded into the BST
instruction register, the identification register will be
connected between TDI and TDO of the IC.
SAA6752HS continues operation.
SAA6752HS continues operation.
SAA6752HS continues operation, but a forced
reconfigure is recommended.
Initialization of boundary scan circuit
Device identification codes
RESPONSE IF EXCEPTION IS DETECTED
SAA6752HS
Product specification

Related parts for SAA6752HS/V103