ISD5116 WINBOND [Winbond], ISD5116 Datasheet - Page 19

• Manufacturer Part Number: ISD5116
• Description: Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
• Manufacturer: WINBOND [Winbond]

In this mode, the elements of the original PASS THROUGH mode do not change. The sections of the
chip not required to add the record path remain powered down. In fact, CFG0 does not change and
remains
CFG1 changes to
Since CFG0 is not changed, it is only necessary to load CFG1. Note that if only CFG0 was changed, it
would be necessary to load both registers.
3.9 MEMO RECORD
The Memo Record mode sets the chip up to record from the local microphone into the chip’s Multilevel
Storage Array. A connected cellular telephone or cordless phone chip set may remain powered down and
is not active in this mode. The path to be used is microphone input to AGC amplifier, then through the
INPUT SOURCE MUX to the SUM1 SUMMING amplifier. From there the path goes through the FILTER
MUX, the LOW PASS FILTER, the SUM2 SUMMING amplifier, then to the MULTILEVEL STORAGE
ARRAY. In this instance, we will select the 5.3 kHz sample rate. The rest of the chip may be powered
down.
October 2000
2. Select the SUM1 MUX input (only) to the S1 SUMMING amplifier—Bits S1M0 and S1M1 control
3. Select the SUM1 SUMMING amplifier path through the FILTER MUX—Bit FLS0 controls the state
4. Power up the LOW PASS FILTER—Bit FLPD controls the power up state of the LOW PASS
5. Select the 6.4 kHz sample rate—Bits FLD0 and FLD1 select the Low Pass filter setting and
6. Select the LOW PASS FILTER input (only) to the S2 SUMMING amplifier—Bits S2M0 and S2M1
1. Power up the AGC amplifier—Bit AGPD controls the power up state of the AGC amplifier. This is
2. Select the AGC amplifier through the INPUT SOURCE MUX—Bit INS0 controls the state of the
3. Select the INPUT SOURCE MUX (only) to the S1 SUMMING amplifier—Bits S1M0 and S1M1
4. Select the SUM1 SUMMING amplifier path through the FILTER MUX—Bit FLS0 controls the state
CFG0=0100 0100 0000 1011 (hex 440B).
CFG1=0000 0000 1100 0101 (hex 00C5).
the state of the SUM1 SUMMING amplifier. These are bits D7 and D8 respectively of CFG1 and
they should be set to the state where D7 is ONE and D8 is ZERO to select the SUM1 MUX (only)
path.
of the FILTER MUX. This is bit D4 of CFG1 and it must be set to ZERO to select the SUM1 SUM-
MING amplifier path.
FILTER stage. This is bit D1 of CFG1 and it must be set to ZERO to power up the LOW PASS
FILTER STAGE.
sample rate to be used during record and playback. These are bits D2 and D3 of CFG1. To
enable the 6.4 kHz sample rate, D2 must be set to ONE and D3 set to ZERO.
control the state of the SUM2 SUMMING amplifier. These are bits D5 and D6 respectively of
CFG1 and they should be set to the state where D5 is ZERO and D6 is ONE to select the LOW
PASS FILTER (only) path.
bit D0 of CFG1 and must be set to ZERO to power up this stage.
INPUT SOURCE MUX. This is bit D9 of CFG0 and must be set to a ZERO to select the AGC am-
plifier.
control the state of the SUM1 SUMMING amplifier. These are bits D7 and D8 respectively of
CFG1 and they should be set to the state where D7 is ZERO and D8 is ONE to select the INPUT
SOURCE MUX (only) path.
of the FILTER MUX. This is bit D4 of CFG1 and it must be set to ZERO to select the SUM1
SUMMING amplifier path.
Page 18