PSD813F1 STMICROELECTRONICS [STMicroelectronics], PSD813F1 Datasheet - Page 103

no-image

PSD813F1

Manufacturer Part Number
PSD813F1
Description
Flash In-System Programmable ISP Peripherals For 8-bit MCUs
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PSD813F1-15J
Manufacturer:
ST
0
Part Number:
PSD813F1-70J
Manufacturer:
ST
0
Part Number:
PSD813F1-90J
Manufacturer:
ST
0
Part Number:
PSD813F1-90U
Manufacturer:
ST
0
Part Number:
PSD813F1-90UI
Manufacturer:
ST
0
Part Number:
PSD813F1-A-15J
Manufacturer:
MAXIM
Quantity:
2 500
Part Number:
PSD813F1-A-15JI
0
Preliminary
EEPROM Write Times
Microcontroller Interface – PSD813F1V AC/DC Parameters
(3.0 V to 3.6 V Versions)
Flash Program, Write and Erase Times
ISC Timing
NOTES: 1. If the maximum time has elapsed between successive writes to an EEPROM page, the transfer of this data to EEPROM cells will
NOTES: 1. Programmed to all zeros before erase.
NOTES: 1. For “non-PLD” programming, erase or in ISC by-pass mode.
Symbol
t
t
t
t
Symbol
t
t
t
t
t
Symbol
EEHWL
BLC
WCB
WCP
t
t
t
t
t
t
t
t
t
t
t
WHQV3
WHQV2
WHQV1
WHWLO
Q7VQV
ISCCF
ISCCH
ISCCL
ISCCF-P
ISCCH-P
ISCCL-P
ISCPSU
ISCPH
ISCPCO
ISCPZV
ISCPVZ
2. The Polling Status DQ7 is valid t
2. These specifications are for writing a page to EEPROM cells.
2. For program or erase PLD only.
begin. Also, bytes cannot be written (loaded) to a page any faster than the indicated minimum type.
(3.0 V to 3.6 V Versions)
TCK Clock Frequency (except for PLD)
TCK Clock High Time
TCK Clock Low Time
TCK Clock Frequency (for PLD only)
TCK Clock High Time (for PLD only)
TCK Clock Low Time (for PLD only)
ISC Port Set Up Time
ISC Port Hold Up Time
ISC Port Clock to Output
ISC Port High-Impedance to Valid Output
ISC Port Valid Output to High-Impedance
Write Protect After Power Up
EEPROM Byte Load Cycle Timing (Note 1)
EEPROM Byte Write Cycle Time
EEPROM Page Write Cycle Time (Note 2)
Program/Erase Cycles (Per Sector)
Flash Program
Flash Bulk Erase (Preprogrammed) (Note 1)
Flash Bulk Erase (Not Preprogrammed)
Sector Erase (Preprogrammed)
Sector Erase (Not Preprogrammed)
Byte Program
Program/Erase Cycles (Per Sector)
Sector Erase Time-Out
DQ7 Valid to Output (DQ7-0) Valid
(Data Polling) (Note 2)
(3.0 V to 3.6 V Versions)
Parameter
Parameter
Parameter
Q7VQV
ns before the data byte DQ0-7 is valid for reading.
(3.0 V to 3.6 V Versions)
Conditions
(Note 1)
(Note 1)
(Note 1)
(Note 2)
(Note 2)
(Note 2)
100,000
10,000
Min
240
240
45
45
13
10
Min
Min
0.2
-15
Max
10
36
36
36
2
100
Typ
Typ
8.5
2.2
10
14
5
4
6
3
1
Min
240
240
51
51
15
10
-20
1200
Max
Max
120
10
30
30
30
30
Max
40
40
40
9
2
PSD813F1-A
cycles
cycles
msec
msec
msec
µsec
Unit
Unit
sec
sec
sec
sec
sec
MHz
MHz
Unit
µs
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
99

Related parts for PSD813F1