NCP1217 ONSEMI [ON Semiconductor], NCP1217 Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
NCP1217
Manufacturer Part Number
NCP1217
Description
Enhanced PWM Current−Mode Controller for High−Power Universal Off−Line Supplies
Manufacturer
ONSEMI [ON Semiconductor]
Datasheet
1.NCP1217.pdf
(18 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NCP1217AD100R2G
Manufacturer:
ON Semiconductor
Quantity:
1 000
Part Number:
NCP1217AD100R2G
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
NCP1217AD65R2G
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
NCP1217AP10
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
NCP1217AP100G
Manufacturer:
ON/安森美
Quantity:
20 000
Company:
Part Number:
NCP1217AP65G
Manufacturer:
ON Semiconductor
Quantity:
232
Part Number:
NCP1217D06DR2G
Manufacturer:
ON/安森美
Quantity:
20 000
Company:
Part Number:
NCP1217D133R2G
Manufacturer:
ON Semiconductor
Quantity:
2 000
Company:
Part Number:
NCP1217D65R2G
Manufacturer:
ON Semiconductor
Quantity:
65
Company:
Part Number:
NCP1217P100G
Manufacturer:
SUPERTEX
Quantity:
16 700
Calculating the V
consumption as soon as V
NCP1217P065 is used and drives a MOSFET with a 30 nC
total gate charge (Qg). The total average current is thus
made of ICC1 (750 mA) plus the driver current,
The DV available to fully startup the circuit (e.g. never reach
the 8.2 V VCC
best case or 4.9 V worse case
capacitor that then needs to supply the NCP1217 with
2.7 mA during a given time until the auxiliary supply takes
over. Suppose that this time was measured at around 15 ms.
CV
Skipping Cycle Mode
the output power demand drops below a given level. This is
accomplished by monitoring the FB pin. In normal
operation, pin 2 imposes a peak current accordingly to the
load value. If the load demand decreases, the internal loop
asks for less peak current. When this setpoint reaches a
determined level (Vpin 1), the IC prevents the current from
decreasing further down and starts to blank the output
pulses: the IC enters the so−called skip cycle mode, also
named controlled burst operation. The power transfer now
depends upon the width of the pulse bunches (Figure 20).
Suppose we have the following component values:
Lp, primary inductance = 350 mH
Fsw, switching frequency = 65 kHz
Ip skip = 600 mA (or 333 mV/Rsense)
Fsw * Qg + 1.95 mA
C w 8.3 mF.
The V
The NCP1217 automatically skips switching cycles when
CC
is calculated using the equation
CC
capacitor can be calculated knowing the IC
Select a 22 mF/25 V and this will fit.
min
CC
during power on) is
. The total current is therefore 2.7 mA.
Capacitor
CC
VCC
reaches 12.8 V. Suppose that a
Figure 18. Typical Waveforms in Short Circuit Conditions
ON
(11.9−7.0)
= 12.8 V
13.7−8.2 + 5.5 V
VCC
. We have a
VCC
C + Dt · i
latch
NCP1217, NCP1217A
min
= 5.6 V
DV
http://onsemi.com
= 7.6 V
or
10
mode with a bunch length of 10 ms over a recurrent
period of 100 ms, then the total power transfer is:
a look at the operation mode versus the FB level
immediately gives the necessary insight.
default), the peak current cannot exceed 1.0 V/Rsense.
When the IC enters the skip cycle mode, the peak current
cannot go below Vpin1/3.3. The user still has the flexibility
to alter this 1.0 V by either shunting pin 1 to ground through
a resistor or raising it through a resistor up to the desired
level. In this later case, care must be taken to keep sufficient
margin between this pin 1 adjustment level and the latchoff
level. Grounding pin 1 permanently invalidates the skip
cycle operation.
1
2
4.1 * 0.1 + 410 mW
FB
DRIVING PULSES
The
To better understand how this skip cycle mode takes place,
When FB is above the skip cycle threshold (1.0 V by
· Lp · Ip 2 · Fsw + 4.1 W
NORMAL CURRENT
MODE OPERATION
SKIP CYCLE OPERATION
I
P(min)
V
CC
theoretical
= 333 mV/R
.
SENSE
power
Figure 19.
. If this IC enters skip cycle
transfer
4.2 V, FB Pin Open
3.2 V, Upper
Dynamic Range
1 V
is
therefore:
Time