NCP5424_05 ONSEMI [ON Semiconductor], NCP5424_05 Datasheet - Page 13
![no-image](/images/no-image-200.jpg)
NCP5424_05
Manufacturer Part Number
NCP5424_05
Description
Dual Synchronous Buck Controller with Input Current Sharing
Manufacturer
ONSEMI [ON Semiconductor]
Datasheet
1.NCP5424_05.pdf
(18 pages)
where:
MOSFET switch−on and switch−off and can be determined
by using the following formula:
where:
then be calculated as:
where:
known, the maximum FET switch junction temperature can
be calculated:
where:
Selection of the Synchronous (Lower) FET
calculated as follows:
where:
except for losses in the internal body diode, because it turns
on into near zero voltage conditions. The MOSFET body
diode will conduct during the non−overlap time and the
P HFET(TOTAL) + P RMS(H) ) P SWH(ON) ) P SWH(OFF)
P
I
R
The upper MOSFET switching losses are caused during
P
P
V
I
t
t
T = 1/f
The total power dissipation in the switching MOSFET can
P
P
P
P
Once the total power dissipation in the switching FET is
T
T
P
R
The switch conduction losses for the lower FET can be
P
I
D = Duty Cycle;
R
The synchronous MOSFET has no switching losses,
RISE
FALL
RMS(H)
OUT
OUT
RMS(H)
SWH(ON)
SWH(OFF)
HFET(TOTAL)
RMS(H)
SWH(ON)
SWH(OFF)
A
HFET(TOTAL)
RMS(L)
J
DS(ON)
qJA
DS(ON)
IN
= FET junction temperature;
= ambient temperature;
P RMS(L) + I RMS 2
= input voltage;
= upper FET junction−to−ambient thermal resistance.
= load current;
= MOSFET rise time (from FET manufacturer’s
= load current;
= MOSFET fall time (from FET manufacturer’s
SW
switching characteristics performance curve);
T J + T A ) [P HFET(TOTAL)
P SWH + P SWH(ON) ) P SWH(OFF)
= maximum switching MOSFET RMS current;
switching characteristics performance curve);
= lower MOSFET conduction losses;
P RMS(H) + I RMS(H) 2
= switching MOSFET conduction losses;
= FET drain−to−source on−resistance
= upper MOSFET switch conduction Losses;
= lower FET drain−to−source on−resistance.
= period.
= upper MOSFET switch−on losses;
= upper MOSFET switch−on losses;
= upper MOSFET switch−off losses;
= upper MOSFET switch−off losses;
+ [I OUT
= total switching (upper) MOSFET losses;
= total switching (upper) FET losses;
+
V IN
I OUT
(1 * D) ] 2
R DS(ON)
6T
(t RISE ) t FALL )
R DS(ON)
R DS(ON)
R qJA ]
http://onsemi.com
NCP5424
13
resulting power dissipation (neglecting reverse recovery
losses) can be calculated as follows:
where:
GATE(H)−to−GA TE(L) delay (from NCP5424 data sheet
Electrical Characteristics section);
MOSFET can then be calculated as:
where:
is known the maximum FET switch junction temperature
can be calculated:
where:
Control IC Power Dissipation
used, V
average MOSFET gate charge current typically dominates
the control IC power dissipation.
P CONTROL(IC) + I CC1 V CC1 ) I BST V BST ) P GATE(H)1
where:
are:
where:
losses are:
P
V
I
Non−overlap
f
The total power dissipation in the synchronous (lower)
P
P
P
Once the total power dissipation in the synchronous FET
T
T
P
R
The power dissipation of the IC varies with the MOSFETs
The IC power dissipation is determined by the formula:
P
I
V
P
P
The upper (switching) MOSFET gate driver (IC) losses
P
Q
f
The lower (synchronous) MOSFET gate driver (IC)
P SWL + V SD
LOAD
SW
CC1
SW
SWL
LFET(TOTAL)
RMS(L)
SWL
A
LFET(TOTAL)
CONTROL(IC)
GATE(H)
GATE(L)
GATE(H)
J
qJA
SD
CC1
GATE(H)
= MOSFET junction temperature;
= ambient temperature;
= switching frequency.
= switching frequency;
= lower FET source−to−drain voltage;
= IC quiescent supply current;
= lower FET junction−to−ambient thermal resistance.
CC
= IC supply voltage;
= lower FET switching losses;
= Switching losses.
P GATE(H) + Q GATE(H)
P GATE(L) + Q GATE(L)
= load current;
T J + T A ) [P LFET(TOTAL)
P LFET(TOTAL) + P RMS(L) ) P SWL
, and the NCP5424 operating frequency. The
= Switch Conduction Losses;
= lower MOSFET gate driver (IC) losses.
= upper MOSFET gate driver (IC) losses;
= upper MOSFET gate driver (IC) losses;
= total upper MOSFET gate charge at V
) P GATE(L)1 ) P GATE(H)2 ) P GATE(L)2
= Synchronous (lower) FET total losses;
= total synchronous (lower) FET losses;
= control IC power dissipation;
time
I LOAD
=
GATE(L)−to−GA TE(H)
non−overlap time
f SW
f SW
R qJA ]
V CC
V BST
f SW
CC
;
or