CS5206-3GDP3 ONSEMI [ON Semiconductor], CS5206-3GDP3 Datasheet - Page 6
![no-image](/images/no-image-200.jpg)
CS5206-3GDP3
Manufacturer Part Number
CS5206-3GDP3
Description
6.0 A Adjustable, and Fixed 3.3 V and 5.0 V Linear Regulators
Manufacturer
ONSEMI [ON Semiconductor]
Datasheet
1.CS5206-3GDP3.pdf
(10 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS5206-3GDP3
Manufacturer:
ON
Quantity:
6 892
CS5206−X the transient response and stability improve with
higher values of capacitor. The majority of applications for
this regulator involve large changes in load current so the
output capacitor must supply the instantaneous load current.
The ESR of the output capacitor causes an immediate drop
in output voltage given by:
output capacitor network consisting of several tantalum and
ceramic capacitors in parallel. This reduces the overall ESR
and reduces the instantaneous output voltage drop under
load transient conditions. The output capacitor network
should be as close as possible to the load for the best results.
Protection Diodes
regulator it is sometimes necessary to add protection diodes.
If the input voltage of the regulator gets shorted, the output
capacitor will discharge into the output of the regulator. The
discharge current depends on the value of the capacitor, the
output voltage and the rate at which V
CS5206−X family of linear regulators, the discharge path is
through a large junction and protection diodes are not
usually needed. If the regulator is used with large values of
output capacitance and the input voltage is instantaneously
shorted to ground, damage can occur. In this case, a diode
connected as shown in Figures 11 and 12 is recommended.
V
V
Figure 11. Protection Diode Scheme for Adjustable
Figure 12. Protection Diode Scheme for Fixed Output
For microprocessor applications it is customary to use an
When large external capacitors are used with a linear
IN
IN
C
C
1
1
V
IN
IN4002 (optional)
V
CS5206−1
Output Regulator
IN
DV + DI
Adj
CS5206−1
IN4002 (optional)
Regulators
C
Gnd
Adj
V
OUT
ESR
V
OUT
CS5206−1, CS5206−3, CS5206−5
R
R
IN
1
2
drops. In the
C
C
2
2
V
http://onsemi.com
OUT
V
OUT
6
Output Voltage Sensing
possible to provide true remote load sensing. Load
regulation is limited by the resistance of the conductors
connecting the regulator to the load. For best results the
fixed regulators should be connected as shown in Figure 13.
occurs when R1 is connected directly to the output pin of the
regulator as shown in Figure 14. If R1 is connected to the
load, R
resistance between the regulator and the load becomes
where R
V
Calculating Power Dissipation and Heat Sink
Requirements
thermal shutdown and safe operating area circuitry to
protect the device. High power regulators such as these
usually operate at high junction temperatures so it is
important to calculate the power dissipation and junction
V
Figure 14. Grounding Scheme for Adjustable Output
IN
IN
Since the CS5206−X is a three terminal regulator, it is not
For the adjustable regulator, the best load regulation
The CS5206−X series of
Figure 13. Conductor Parasitic Resistance can be
Minimized with the Above Grounding Scheme for
C
C
is multiplied by the divider ratio and the effective
= conductor parasitic resistance.
V
Regulator to Minimize Parasitics
IN
V
CS5206−1
IN
CS5206−X
Fixed Output Regulators
Adj
Gnd
R C
V
OUT
V
OUT
R1 ) R2
R1
linear regulators includes
R
R
R
1
2
Conductor Parasitic
C
R
C
Resistance
Conductor Parasitic
Resistance
R
LOAD
R
LOAD