M30622 Mitsubishi, M30622 Datasheet - Page 52

no-image

M30622

Manufacturer Part Number
M30622
Description
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Manufacturer
Mitsubishi
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
M30622-109GP
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
M30622ECFP
Manufacturer:
INFINEON
Quantity:
607
Part Number:
M30622ECFP
Manufacturer:
ST
0
Part Number:
M30622EECFP
Manufacturer:
MIT
Quantity:
20 000
Part Number:
M30622F8PA04GP
Manufacturer:
MIT
Quantity:
105
Part Number:
M30622F8PA04GP
Manufacturer:
RENESAS
Quantity:
1 000
Part Number:
M30622F8PA04GP
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
M30622F8PFP
Manufacturer:
MIT
Quantity:
20 000
Part Number:
M30622F8PFP#D5C
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
M30622F8PFP#U3C
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
M30622F8PFP#U5C
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
M30622F8PFPD5
Manufacturer:
RENESAS
Quantity:
893
Part Number:
M30622F8PFPU3C
Manufacturer:
RENESAS
Quantity:
5 002
Part Number:
M30622F8PFPU5U
Manufacturer:
STM
Quantity:
4 667
Part Number:
M30622F8PGP
Manufacturer:
MIT
Quantity:
20 000
Interrupt
Hardware Interrupts
Hardware interrupts are classified into two types — special interrupts and peripheral I/O interrupts.
(1) Special interrupts
(2) Peripheral I/O interrupts
• Reset
• NMI interrupt
• DBC interrupt
• Watchdog timer interrupt
• Single-step interrupt
• Address match interrupt
A peripheral I/O interrupt is generated by one of built-in peripheral functions. Built-in peripheral func-
tions are dependent on classes of products, so the interrupt factors too are dependent on classes of
products. The interrupt vector table is the same as the one for software interrupt numbers 0 through
31 the INT instruction uses. Peripheral I/O interrupts are maskable interrupts.
• Bus collision detection interrupt
• DMA0 interrupt, DMA1 interrupt
• Key-input interrupt
• A-D conversion interrupt
• UART0, UART1, UART2/NACK, SI/O3 and SI/O4 transmission interrupt
• UART0, UART1, UART2/ACK, SI/O3 and SI/O4 reception interrupt
• Timer A0 interrupt through timer A4 interrupt
• Timer B0 interrupt through timer B5 interrupt
• INT0 interrupt through INT5 interrupt
Tentative Specifications REV.A
Special interrupts are non-maskable interrupts.
Reset occurs if an “L” is input to the RESET pin.
_______
An NMI interrupt occurs if an “L” is input to the NMI pin.
This interrupt is exclusively for the debugger, do not use it in other circumstances.
Generated by the watchdog timer.
This interrupt is exclusively for the debugger, do not use it in other circumstances. With the debug
flag (D flag) set to “1”, a single-step interrupt occurs after one instruction is executed.
An address match interrupt occurs immediately before the instruction held in the address indicated by
the address match interrupt register is executed with the address match interrupt enable bit set to “1”.
If an address other than the first address of the instruction in the address match interrupt register is set,
no address match interrupt occurs. For address match interrupt, see 2.11 Address match Interrupt.
This is an interrupt that the serial I/O bus collision detection generates.
These are interrupts that DMA generates.
A key-input interrupt occurs if an “L” is input to the KI pin.
This is an interrupt that the A-D converter generates.
These are interrupts that the serial I/O transmission generates.
These are interrupts that the serial I/O reception generates.
These are interrupts that timer A generates
These are interrupts that timer B generates.
An INT interrupt occurs if either a rising edge or a falling edge or a both edge is input to the INT pin.
Note 1:
________
________
S
_______
______
pecifications in this manual are tentative and subject to change.
In M30623 (80-pin package), can not use INT
P1
5
/D
13
/INT
_______
3
to P1
________
7
/D
15
/INT
_______
____________
5
have no corresponding external pin.
52
_______
___
_______
3
to INT
_______
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
5
as the interrupt factors, because
Mitsubishi microcomputers
M16C / 62T Group
______

Related parts for M30622