UPB587G NEC, UPB587G Datasheet
UPB587G
Available stocks
Related parts for UPB587G
UPB587G Summary of contents
Page 1
... ORDERING INFORMATION PART NUMBER PACKAGE P PB1509GV-E1 8 pin plastic SSOP (175 mil) Remarks : To order evaluation samples, please contact your local NEC sales office. (Part number for sample order: P PB1509GV) Document No. P10769EJ2V0DS00 (2nd edition) Date Published September 1997 N Printed in Japan DATA SHEET BIPOLAR DIGITAL INTEGRATED CIRCUIT ...
Page 2
... PIN CONNECTION (Top View PRODUCT LINE-UP Product No (mA) (V) P PB587 G 5.5 2.2 to 3.5 P PB1509 GV 5.0 2.2 to 5.5 Remarks This table shows the TYP values of main parameters. Please refer to ELECTRICAL CHARACTERISTICS. P PB587G is discontinued. INTERNAL BLOCK DIAGRAM D IN CLK IN 2 Pin NO ...
Page 3
SYSTEM APPLICATION EXAMPLE One of the example for usage This block diagram schematically shows the P PB1509GV’s location in one of the example application system. The other applications are also acceptable for divider use. VCO N ...
Page 4
Pin Explanations Applied Pin No. Symbol Voltage Voltage 1 V 2.2 to 5.5 CC1 • 1.7 to 4.95 • 1.7 to 4.95 4 GND 0 5 SW1 H/L 6 SW2 H/L • 7 OUT 1.0 to ...
Page 5
... MHz to 500 MHz in2 in = 200 : V R out L V Connection in the test circuit IH1 V Connection in the test circuit IL1 V Connection in the test circuit IH2 V Connection in the test circuit IL2 PB1509GV RATINGS UNIT 6.0 V 6.0 V 250 mW ð40 to +85 qC ð55 to +150 qC NOTICE V qC MIN ...
Page 6
... Oscilloscope for measuring output swing (In measuring output power on Spectrum Analyzer, oscilloscope should be turned off.) Divide Ratio Setting SW2 1/2 1/4 SW1 L 1/4 1 pin should be connected to V CC1 L: SW pin should be opened or connected to GND. 6 Power Supply 1000 CC2 OUT 7 C6 SW2 6 C5 SW1 ...
Page 7
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD V CC1 Component List No. Value 1000 pF 150 : Note R1 Note For Output load of IC determined as follows ...
Page 8
CHARACTERISTIC CURVES Circuit Current vs. Supply Voltage –40° +25° +85° Recommended operating range Supply Voltage V ...
Page 9
Input power vs. Input frequency +25° –40° +85° Guaranteed –10 operating window –20 – +85°C A – +25°C A – –40°C A ...
Page 10
Divide by 4 mode (Guaranteed operating window: V Input power vs. Input frequency Guaranteed –10 operating window – 2.2 V ...
Page 11
Divide by 8 mode (Guaranteed operating window: V Input power vs. Input frequency Guaranteed –10 operating window – 2.2 V ...
Page 12
S vs. Input Frequency REF 1.0 Units/ 2 200.0 mUnits/ 55.375 – 142.79 MARKER 2 700.0 MHz 3 START 0.050000000 GHz STOP 1.000000000 GHz S vs. Output Frequency REF 1.0 Units/ 200.0 mUnits/ START ...
Page 13
PACKAGE DIMENSIONS (UNIT: mm) 8 PIN PLASTIC SSOP (175 mil 3.0 MAX. 0.65 0.575 MAX. Detail of lead end 4.94±0.2 3.2±0.1 0.5±0.2 +0.10 0.10 M 0.3 –0. PB1509GV 0.87±0.2 0.15 13 ...
Page 14
... Form a ground pattern as wide as possible to minimize ground impedance (to prevent undesired operation). (3) Keep the wiring length of the ground pins as short as possible. (4) Connect a bypass capacitor (e.g. 1000 pF) to the V RECOMMENDED SOLDERING CONDITIONS This product should be soldered in the following recommended conditions. Other soldering methods and conditions than the recommended conditions are to be consulted with our sales representatives ...
Page 15
PB1509GV 15 ...
Page 16
... Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance ...