ZL50020GAC ZARLINK [Zarlink Semiconductor Inc], ZL50020GAC Datasheet - Page 31
![no-image](/images/no-image-200.jpg)
ZL50020GAC
Manufacturer Part Number
ZL50020GAC
Description
Enhanced 2 K Digital Switch
Manufacturer
ZARLINK [Zarlink Semiconductor Inc]
Datasheet
1.ZL50020GAC.pdf
(83 pages)
- Current page: 31 of 83
- Download datasheet (683Kb)
10.0
This feature allows for fast initialization of the connection memory after power up.
10.1
1. Set MBPE (bit 3) in the Control Register (CR) from low to high.
2. Configure BPD2 - 0 (bits 3 - 1) in the Internal Mode Selection (IMS) register to the desired values to be loaded
3. Start the block programming by setting MBPS (bit 0) in the Internal Mode Selection Register (IMS) high. The val-
The following tables show the resulting values that are in the CM_L and CM_H connection memory locations.
Note: Bits 15 to 5 are reserved in Connection Memory High and should always be 0.
It takes at least two frame periods (250 µs) to complete a block program cycle.
MBPS (bit 0) in the Control Register (CR) will automatically reset to a low position after the block programming
process has completed.
MBPE (bit 3) in the Internal Mode Selection (IMS) register must be cleared from high to low to terminate the block
programming process. This is not an automatic action taken by the device and must be performed manually.
Note: Once the block program has been initiated, it can be terminated at any time prior to completion by setting
MBPS (bit 0) in the Control Register (CR) or MBPE (bit 3) in the Internal Mode Selection (IMS) register to low. If the
MBPE bit was used to terminate the block programming, the MBPS bit will have to be set low before enabling other
device operations.
11.0
This device has two main operating modes - Divided Clock mode and Multiplied Clock mode.
In Multiplied Clock mode, output clocks and frame pulses are generated from an internal high-speed clock
synchronized to CKi and FPi. Therefore, all specified output clock rates and data rates are available on CKo0-3 and
STio0-31. In Divided Clock mode, output clocks and frame pulses are directly divided from CKi/FPi. Therefore, the
output clock rate cannot exceed the CKi rate (the output data rates are also limited as per Table 1). The input data
rate cannot exceed the CKi rate in either Multiplied or Divided Clock modes, because input data are always
sampled directly by CKi.
Value
Value
Bit
Bit
into CM_L.
ues stored in BPD2 - 0 will be loaded into bits 2 - 0 of all CM_L positions. The remaining CM_L locations (bits 15
- 3) and the programmable values in the CM_H (bits 4 - 0) will be loaded with zero values.
Memory Block Programming Procedure
Device Operation in Divided Clock and Multiplied Clock Modes
Connection Memory Block Programming
15
15
0
0
14
14
0
0
13
13
0
0
Table 6 - Connection Memory High After Block Programming
Table 5 - Connection Memory Low After Block Programming
12
12
0
0
11
11
0
0
10
10
0
0
Zarlink Semiconductor Inc.
9
0
9
0
ZL50020
8
0
8
0
31
7
0
7
0
6
0
6
0
5
0
5
0
4
0
4
0
3
0
3
0
BPD2
2
2
0
BPD1
Data Sheet
1
0
1
BPD0
0
0
0
Related parts for ZL50020GAC
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![SL1430](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
Zarlink Semiconductor Inc [TV IF PREAMPLIFIER]
Manufacturer:
Zarlink Semiconductor
Datasheet:
![MT312C](/images/no-image3.png)
Part Number:
Description:
Satellite Channel Decoder
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![MSC60028/IG/DP2S](/images/no-image3.png)
Part Number:
Description:
Power Factor Controller
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![P10C68-](/images/no-image3.png)
Part Number:
Description:
CMOS/SNOS NVSRAM HIGH PERFORMANCE 8 K x 8 NON-VOLATILE STATIC RAM
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL2009KG](/images/no-image3.png)
Part Number:
Description:
Dual stage IF amplifier for cable tuners
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL2101C](/images/no-image3.png)
Part Number:
Description:
Synthesized Broadband Converter with Programmable Power
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL2150KG](/images/no-image3.png)
Part Number:
Description:
Cable Tuner Front End LNA with AGC
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL2150LH2S](/images/no-image3.png)
Part Number:
Description:
Front End Power Splitter with AGC
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL2524HP](/images/no-image3.png)
Part Number:
Description:
1.3GHz Dual Wideband Logarithmic Amplifier
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL2610IG](/images/no-image3.png)
Part Number:
Description:
Wide Dynamic Range Image Reject MOPLL
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL1451NADP](/images/no-image3.png)
Part Number:
Description:
WIDEBAND PLL FM DETECTOR FOR SATELLITE TV
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL1452NAMP](/images/no-image3.png)
Part Number:
Description:
WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL161](/images/no-image3.png)
Part Number:
Description:
WIDEBAND LOG IF STRIP AMPLIFIER
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL1613CDP](/images/no-image3.png)
Part Number:
Description:
WIDEBAND LOG IF STRIP AMPLIFIER
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL1640](/images/no-image3.png)
Part Number:
Description:
THIS DOCUMENT IS FOR MAINTENANCE PURPOSES ONLY AND IS NOT RECOMMENDED FOR NEW DESIGNS
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet: