C8051F964-A-GQ Silicon Labs, C8051F964-A-GQ Datasheet - Page 60

• Manufacturer Part Number: C8051F964-A-GQ
• Description: 8-bit Microcontrollers - MCU 64KB DC-DC LCD AES
• Manufacturer: Silicon Labs

Specifications of C8051F964-A-GQ

• Rohs: yes
• Core: 8051
• Processor Series: C8051
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 24.5 MHz
• Program Memory Size: 64 KB
• Data Ram Size: 8 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 1.8 V to 3.8 V
• Operating Temperature Range: - 40 C to + 85 C
• Package / Case: QFP-80
• Mounting Style: SMD/SMT

C8051F96x
60
Table 4.4. Digital Supply Current with DC-DC Converter Disabled (Continued)
–40 to +85 °C, 25 MHz system clock unless otherwise specified.
Digital Supply Current— Low Power Idle Mode, All peripheral clocks enabled (PCLKEN = 0x0F)
(CPU Inactive, not fetching instructions from flash)
I
I
Digital Supply Current— Low Power Idle Mode, All Peripheral Clocks Disabled (PCLKEN = 0x00)
(CPU Inactive, not fetching instructions from flash)
I
I
Digital Supply Current—Suspend Mode
Digital Supply Current 
(Suspend Mode)
Notes:
BAT
BAT
BAT
BAT
1. Active Current measure using typical code loop - Digital Supply Current depends upon the particular code
2. Includes oscillator and regulator supply current.
3. Based on device characterization data; Not production tested.
4. Measured with one-shot enabled.
5. Low-Power Idle mode current measured with CLKMODE = 0x04, PCON = 0x01, and PCLKEN = 0x0F.
6. Using SmaRTClock osillator with external 32.768 kHz CMOS clock. Does not include crystal bias current.
7. Low-Power Idle mode current measured with CLKMODE = 0x04, PCON = 0x01, and PCLKEN = 0x00.
2, 6
2, 7
Frequency Sensitivity
Frequency Sensitivity
being executed. Digital Supply Current depends on the particular code being executed. The values in this
table are obtained with the CPU executing a mix of instructions in two loops: djnz R1, $, followed by a loop
that accesses an SFR, and moves data around using the CPU (between accumulator and b-register). The
supply current will vary slightly based on the physical location of this code in flash. As described in the Flash
Memory chapter, it is best to align the jump addresses with a flash word address (byte location /4), to
minimize flash accesses and power consumption.
Parameter
3
3
(includes external oscillator/GPIO current)
(includes external oscillator/GPIO current)
(includes SmaRTClock oscillator current)
(includes low power oscillator current)
(includes low power oscillator current)
(includes precision oscillator current)
(includes precision oscillator current)
V
V
V
BAT
V
V
BAT
BAT
V
V
BAT
BAT
BAT
BAT
V
V
V
V
= 1.8–3.8 V, F = 32.768 kHz
BAT
BAT
BAT
BAT
= 1.8–3.8 V, F = 24.5 MHz
= 1.8–3.8 V, F = 24.5 MHz
= 1.8–3.8 V, F = 20 MHz
= 1.8–3.8 V, F = 20 MHz
= 1.8–3.8 V, T = 25
= 1.8–3.8 V, T = 25
= 1.8 V, F = 1 MHz
= 3.8 V, F = 1 MHz
= 1.8 V, F = 1 MHz
= 3.8 V, F = 1 MHz
V
V
Conditions
BAT
BAT
Rev. 0.5
= 1.8 V
= 3.8 V
°
°
C
C
Min
—
—
—
—
—
—
—
—
—
—
—
—
—
232
1.07
Typ
270
280
487
340
47
1.5
11
90
94
77
84
5
5
5
Max
1.9
—
—
—
—
—
—
—
—
—
—
—
—
µA/MHz
µA/MHz
Units
mA
mA
µA
µA
µA
µA
µA
µA
µA
µA