MPC8536BVTATLA Freescale Semiconductor, MPC8536BVTATLA Datasheet - Page 75

• Manufacturer Part Number: MPC8536BVTATLA
• Description: Microprocessors - MPU 8536 NON E
• Manufacturer: Freescale Semiconductor

Specifications of MPC8536BVTATLA

• Product Category: Microprocessors - MPU
• Rohs: yes
• Processor Series: PowerQUICC III
• Core: e500
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 250 MHz
• Program Memory Size: 32 KB
• Data Ram Size: 512 KB
• Interface Type: I2C, USB
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: 0 C to + 105 C
• Mounting Style: SMD/SMT
• Package / Case: MAPBGA-783

2.13.2
This table provides the eSDHC AC timing specifications as defined in the following figure.
Freescale Semiconductor
At recommended operating conditions (see
At recommended operating conditions (see
SD_CLK clock frequency:
SD_CLK clock frequency - identification mode
SD_CLK clock low time - High speed/Full speed mode
SD_CLK clock high time - High speed/Full speed mode
SD_CLK clock rise and fall times
Input setup times: SD_CMD, SD_DATx, SD_CD to
SD_CLK
Input hold times: SD_CMD, SD_DATx, SD_CD to SD_CLK
Output delay time: SD_CLK to SD_CMD, SD_DATx valid
Notes:
1. The symbols used for timing specifications herein follow the pattern of t
2. In full speed mode, clock frequency value can be 0–25 MHz for a SD/SDIO card and 0–20 MHz for a MMC card. In high speed
3. 0 Hz means to stop the clock. The given minimum frequency range is for cases were a continuous clock is required.
4. To satisfy setup timing, one way board routing delay between Host and Card, on SD_CLK, SD_CMD and SD_DATx should
5. C
6. The parameter values apply to both full speed and high speed modes.
Output low voltage
Output high voltage
Output low voltage
Notes:
1. The min V
2. Open drain mode for MMC cards only.
for inputs and t
high speed mode device timing (SHS) clock reference (K) going to the high (H) state, with respect to the output (O) reaching
the invalid state (X) or output hold time. Note that, in general, the clock reference symbol representation is based on five letters
representing the clock of a particular functional. For rise and fall times, the latter convention is used with the appropriate letter:
R (rise) or F (fall).
mode, clock frequency value can be 0–50 MHz for a SD/SDIO card and 0–52MHz for a MMC card.
not exceed 1 ns.
CARD
Characteristic
≤10 pF, (1 card), and C
eSDHC AC Timing Specifications
IL
and V
(first three letters of functional block)(reference)(state)(signal)(state)
SD/SDIO Full speed/high speed mode
MPC8535E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 5
IH
Table 55. eSDHC interface DC Electrical Characteristics (continued)
MMC Full speed/high speed mode
Parameter
values are based on the respective min and max OV
L
Symbol
= C
V
V
V
OH
OL
OL
Table 56. eSDHC AC Timing Specifications
BUS
Table
Table
+ C
3)
3)
I
HOST
OL
= 100uA @OVDDmin
+C
I
OH
Condition
I
OL
CARD
= -100 uA
= 2 mA
≤ 40 pF
Symbol
t
t
t
t
t
t
t
SHSKHOV
SHSCKR/
SHSIVKH
SHSIXKH
f
SHSCKH
SHSCKF
SHSCKL
f
SHSCK
SIDCK
1
for outputs. For example, t
(first three letters of functional block)(signal)(state) (reference)(state)
OV
IN
DD
Min
—
—
values found in
7/10
7/10
Min
100
- 0.2
2.5
2.5
–3
—
0
0
0.125 * OVDD
25/50
20/52
Max
Max
400
0.3
—
—
—
—
—
Table
3
3
FHSKHOV
Electrical Characteristics
3.
symbolizes eSDHC
MHz
Unit
KHz
Unit
ns
ns
ns
ns
ns
ns
—
—
V
Notes
Notes
4,5,6
—
2, 5
3, 5
5,6
5,6
2
2
5
5
5
75