1893YI-10LFT IDT, 1893YI-10LFT Datasheet - Page 63

• Manufacturer Part Number: 1893YI-10LFT
• Description: Ethernet ICs 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER
• Manufacturer: IDT

Specifications of 1893YI-10LFT

• Rohs: yes
• Part # Aliases: ICS1893YI-10LFT

8.2 Register 0: Control Register
8.2.1 Reset (bit 0.15)
ICS1893 Rev C 6/6/00
Table 8-5
modes of the ICS1893.
•
•
•
Note:
Table 8-5.
† Whenever the PHY address of
‡ As per the IEEE Std 802.3u, during any write operation to any bit in this register, the STA must write the default value
This bit controls the software reset function. Setting this bit to logic one initiates an ICS1893 software reset
during which all Management Registers are set to their default values and all internal state machines are
set to their idle state. For a detailed description of the software reset process, see
“ Software Reset”
During reset, the ICS1893 leaves bit 0.15 set to logic one and isolates all STA management register
accesses. However, the reset process is not complete until bit 0.15 (a Self-Clearing bit), is set to logic zero,
which indicates the reset process is terminated.
0.15
0.14
0.13
0.12
0.11
0.10
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Bit
•
•
to all Reserved bits.
The Control Register is accessible through the MII Management Interface.
Its operation is independent of the MAC/Repeater Interface configuration.
It is fully compliant with the ISO/IEC Control Register definition.
ICS1893 - Release
Is equal to 00000 (binary), the Isolate bit 0.10 is logic one.
Is not equal to 00000, the Isolate bit 0.10 is logic zero.
Reset
Loopback enable
Data rate select
Auto-Negotiation enable
Low-power mode
Isolate
Auto-Negotiation restart
Duplex mode
Collision test
IEEE reserved
IEEE reserved
IEEE reserved
IEEE reserved
IEEE reserved
IEEE reserved
IEEE reserved
For an explanation of acronyms used in
lists the bits for the Control Register, a 16-bit register used to establish the basic operating
Control Register (Register 0 [0x00]
Definition
.
Table
Copyright © 2000, Integrated Circuit Systems, Inc.
All rights reserved.
No effect
Disable Loopback mode
10 Mbps operation
Disable Auto-Negotiation Enable Auto-Negotiation
Normal power mode
No effect
No effect
Half-duplex operation
No effect
Always 0
Always 0
Always 0
Always 0
Always 0
Always 0
Always 0
8-16:
When Bit = 0
63
Table
8-5, see
ICS1893 enters Reset
mode
Enable Loopback mode
100 Mbps operation
Low-power mode
Isolate ICS1893 from MII
Restart Auto-Negotiation
Full-duplex operation
Enable collision test
N/A
N/A
N/A
N/A
N/A
N/A
N/A
When Bit = 1
Chapter 1, “ Abbreviations and Acronyms”
Chapter 8 Management Register Set
cess
Section 5.1.2.3,
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Ac-
RO
RO
RO
RO
RO
RO
RO
SC
SC
SF
–
–
–
–
–
–
–
–
–
–
–
–
–
–
fault
0/1†
De-
June, 2000
0‡
0‡
0‡
0‡
0‡
0‡
0‡
0
0
1
1
0
0
0
0
0/4†
Hex
3
0
0
.