DS3172 Maxim Integrated, DS3172 Datasheet - Page 72
![no-image](/images/no-image-200.jpg)
DS3172
Manufacturer Part Number
DS3172
Description
Network Controller & Processor ICs Dual DS3/E3 Single Chip Transceiver
Manufacturer
Maxim Integrated
Datasheet
1.DS3171.pdf
(234 pages)
Specifications of DS3172
Part # Aliases
90-31720-000
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 72 of 234
- Download datasheet (2Mb)
DS3171/DS3172/DS3173/DS3174
be framing errors if a framed mode is enabled. When the DS3 framed AIS signal is initiated or terminated, in
addition to no BPV or CV errors, there should be no framing or P-bit (parity) or CP-bit errors introduced.
The AIS signal generated at the top level will not generate BPV errors but may generate P-bit and CP-bit errors
when the signal is initiated and terminated. The framed DS3 AIS signal will not cause the far end receiver to re-
sync when the signal is initiated, but it may cause a re-sync when terminated if the DS3 frame position in the
framer is changed while the DS3 AIS signal is being generated. A sequence of events can be executed which will
enable the initiation and termination of DS3 AIS or unframed all ones at the top level without any errors introduced.
The sequence will only work when the automatic AIS generation is not enabled. CV and P-bit errors can occur
when AIS is automatically generated and cannot be avoided. This sequence to generate an error free DS# AIS at
the top level is to have the DS3 AIS or unframed all ones signal initiate in the DS3 framer, and a few frames sent
before initiating or terminating the DS3 AIS or unframed all ones at the top level. After the top level AIS signal is
activated, the AIS signal in the framer can be terminated, DLB activated and diagnostic patterns generated. The
DS3 AIS signal generated at the top level will not change frame alignment after starting even if the DS3 frame
position in the framer is changed.
The transmit line AIS generator at the top level can generate AIS signals even when the framer is looped back
using DLB, but not when the line is looped back using LLB. The AIS signal generated in the framer will be looped
back to the receive side when DLB is activated.
The receive framer can detect both unframed all ones AIS and DS3 framed AIS patterns. When in DS3 framing
modes, both framed DS3 AIS and unframed all ones can be detected. In E3 framing modes E3 AIS, which is
unframed all ones, is detected.
The receive payload interface going to the RSERn pin or the BERT logic can have an unframed all ones AIS signal
replacing the receive signal, this is called Payload AIS. The all ones AIS signal is generated from either the DS3/E3
framer or the downstream top level unframed all ones AIS generator. The unframed all ones AIS signal generated
in the framer will be looped back to the transmit side when PLB is activated. The unframed all ones AIS signal
generated at the top level will be sent to the RSERn pin and other receive logic, but not to the transmit side while
PLB is activated. The top level AIS generator is used when a downstream AIS signal is desired while payload loop
back is activated and is enabled by default after rest and must be cleared during configuration. Note that the
downstream AIS circuit in the framer, when a DS3 mode is selected, enforces the OOF to be active for 2.5 ms
before activating when automatic AIS in the framer is enabled. The top level downstream AIS will be generated
with no delay when OOF is detected when automatic AIS at the top level is enabled.
There is no detection of any AIS signal on the transmit payload signal from the TSERn pin or anywhere on the
transmit data path.
The transmit AIS generator at the top level can also be activated with a software bit or automatically when DLB is
activated. The receive AIS generator in the framer can be activated with a software bit, and automatically when
AIS, LOS or OOF are detected. The receive payload AIS generator at the top level can be activated with a software
bit or automatically when LOS, DS3/E3 OOF, LLB or PLB is activated.
72
Related parts for DS3172
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![MAX3261CCJ](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3263CAG](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX7528KCWP](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX8809AETL+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX1535CETJ+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
![DS2741N+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
![MAX13450EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX13451EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX17497BATE+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
![MAX17502FATB+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
![MAX1978EVKIT](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
![MAX2606EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2608EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2831EVKIT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
![MAX4888CETI+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: