UPMU-M3L1X-B-EK Silicon Labs, UPMU-M3L1X-B-EK Datasheet - Page 49

no-image

UPMU-M3L1X-B-EK

Manufacturer Part Number
UPMU-M3L1X-B-EK
Description
Daughter Cards & OEM Boards UDP SiM3L1xx MCU Card (no LCD)
Manufacturer
Silicon Labs
Datasheet

Specifications of UPMU-M3L1X-B-EK

Product
MCU Cards
Core
ARM Cortex M3
Data Bus Width
32 bit
Description/function
MCU Card (No LCD) to use with UDP Motherboard
Interface Type
I2C, SPI, UART
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Tool Is For Evaluation Of
SiM3L1xx
For Use With
SiM3L1xx
4.8. Analog
4.8.1. 12-Bit Analog-to-Digital Converter (SARADC0)
The SARADC0 module on SiM3L1xx devices implements the Successive Approximation Register (SAR) ADC
architecture. The key features of the module are as follows:
4.8.2. 10-Bit Digital-to-Analog Converter (IDAC0)
The IDAC module takes a digital value as an input and outputs a proportional constant current on a pin. The IDAC
module includes the following features:
4.8.3. Low Current Comparators (CMP0, CMP1)
The Comparators take two analog input voltages and output the relationship between these voltages (less than or
greater than) as a digital signal. The low power comparator (CMPn) module includes the following features:


























Conversion complete, multiple conversion complete, and FIFO overflow and underflow flags and interrupts
Sequencer allows up to eight sources to be automatically scanned using one of four channel characteristic
Support for multiple data packing formats, including: single 10-bit sample per word, dual 10-bit samples per
Single-ended 12-bit and 10-bit modes.
Supports an output update rate of 250 k samples per second in 12-bit mode or 1 M samples per second in
10-bit mode.
Operation in low power modes at lower conversion speeds.
Selectable asynchronous hardware conversion trigger with hardware channel select.
DC offset cancellation.
Automatic result notification with multiple programmable thresholds.
Support for Burst Mode, which produces one set of accumulated data per conversion-start trigger with
programmable power-on settling and tracking time.
Non-burst mode operation can also automatically accumulate multiple conversions, but a conversion start
is required for each conversion.
supported.
Flexible output data formatting.
profiles without software intervention.
Eight-word conversion data FIFO for DMA operations.
Includes two internal references (1.65 V fast-settling, 1.2/2.4 V precision), support for an external
reference, and support for an external signal ground.
10-bit current DAC with support for four timer, up to seven external I/O and on demand output update
triggers.
Ability to update on rising, falling, or both edges for any of the external I/O trigger sources.
Supports an output update rate greater than 600 k samples per second.
Support for three full-scale output modes: 0.5 mA, 1.0 mA and 2.0 mA.
Four-word FIFO to aid with high-speed waveform generation or DMA interactions.
Individual FIFO overrun, underrun, and went-empty interrupt status sources.
word, or four 8-bit samples per word.
Support for left- and right-justified data.
Multiple sources for the positive and negative inputs, including VBAT, VREF, and 8 I/O pins.
Two outputs available: a digital synchronous latched output and a digital asynchronous raw output.
Programmable hysteresis and response time.
Falling or rising edge interrupt options on the comparator output.
6-bit programmable reference divider.
Rev 0.5
SiM3L1xx
49

Related parts for UPMU-M3L1X-B-EK