TC58FVM7B5BTG-65 Toshiba, TC58FVM7B5BTG-65 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/6/668/toshiba_sml.jpg)
TC58FVM7B5BTG-65
Manufacturer Part Number
TC58FVM7B5BTG-65
Description
IC FLASH 128MBIT 65NS 56TSOP
Manufacturer
Toshiba
Datasheet
1.TC58FVM7T5BTG65.pdf
(88 pages)
Specifications of TC58FVM7B5BTG-65
Format - Memory
FLASH
Memory Type
FLASH - Nor
Memory Size
128M (16Mx8, 8Mx16)
Speed
65ns
Interface
Parallel
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
56-TSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
10. OPERATION MODES
data polling. When incorporating the device into a design, please refer to the timing charts and flowcharts in combination with the
descriptions below.
In addition to the Read, Write and Erase Modes, the TC58FVM7(T/B)5B features many functions including block protection and
10.1. Read Mode
Software Reset Command releases The ID Read Mode, releases the lock state when an automatic operation ends abnormally,
and sets the device to Read Mode. Hardware Reset terminates operation of the device and resets it to Read Mode. When
reading data without changing the address immediately after power-on, the host should input Hardware Reset or change CE
from H to L.
10.2. ID Read Mode
programmers to identify the device type automatically.
10.3. Standby Mode
state.
10.4. Auto-Sleep Mode
automatically enter Sleep Mode and the current will be reduced to the standby current (I
process of performing simultaneous operation, the device will not enter Standby Mode but will instead cause the operating
current to flow. Because the output data is latched, data is output in Sleep Mode. When the address is changed, Sleep Mode is
automatically released, and data from the new address is output.
10.5. Output Disable Mode
(1) Applying V
(1) Control using CE and RESET
(2) Input command sequence
(2) Control using RESET only
To read data from the memory cell array, set the device to Read Mode.
The device is automatically set to Read Mode immediately after power-on or on completion of an automatic operation. The
ID Read Mode is used to read the device maker code and device code. The mode is useful in that it allows EPROM
Access time in ID Read Mode is the same as that in Read Mode. For a list of the codes, please refer to the ID Code Table.
ID read can be executed in two ways, as follows:
TC58FVM7(T/B)5B has two ways to put the device into Standby Mode. In Standby Mode, DQ is put into the High-Impedance
This function suppresses power dissipation during reading. If the address input does not change for 150 ns, the device will
Inputting V
maker code from address 00h and the device code from address 01h. Releasing V
Mode. With this method, all banks are set to ID Read Mode; thus, simultaneous operation cannot be performed.
current will be reduced to the standby current (I
operation, the device will not enter Standby Mode but will instead cause the operating current to flow.
be reduced to the standby current (I
method will terminate the current operation and set the device to Standby Mode. This is a hardware reset and is described
later.
ID Read Mode. Banks are specified by inputting the bank address (BK) in the third Bus Write cycle of the Command cycle.
To read an ID code, the bank address as well as the ID read address must be specified (with
maker code is output from address BK + 00; the device code is output from address BK + 01. From other banks, data is
output from the memory cells. Inputting a Reset command releases ID Read Mode and returns the device to Read Mode.
Mainly EPROM programmers use this method. Applying V
With the device in Read Mode, input V
With the device in Read Mode, input V
With this method simultaneous operation can be performed. Inputting an ID Read command sets the specified bank to
IH
ID
to OE disables output from the device and sets DQ to High-Impedance.
to A9
DDS1
SS
). Even if the device is in the process of performing simultaneous operation, this
DD
± 0.3 V to RESET . The device will enter Standby Mode and the current will
± 0.3 V to CE and RESET . The device will enter Standby Mode and the
DDS1
). However, if the device is in the process of performing simultaneous
ID
to A9 sets the device to ID Read Mode, outputting the
TC58FVM7(T/B)5B(TG/XG)65
ID
DDS2
from A9 returns the device to Read
). However, if the device is in the
WP
/ACC
2006-05-10 10/88
= V
IH
or V
IL
). The