MD4832-D512-V3Q18-X/Y SanDisk, MD4832-D512-V3Q18-X/Y Datasheet - Page 16

• Manufacturer Part Number: MD4832-D512-V3Q18-X/Y
• Description: IC MDOC G3 512MB 85-FBGA
• Manufacturer: SanDisk

Specifications of MD4832-D512-V3Q18-X/Y

• Format - Memory: FLASH
• Memory Type: FLASH - Nand
• Memory Size: 512M (64M x 8)
• Speed: 55ns
• Interface: Parallel
• Voltage - Supply: 2.5 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 585-1140

7x10 FBGA Package
13
A[12:11]
A[10:8]
A[7:4]
A[3:0]
D[15:14]
D[13:12]
D[11:8]
D[7:6]
D[5:3]
D[2:0]
CE#
OE#
WE#
ID[1:0]
LOCK#
IF_CFG
BUSY#
RSTIN#
CLK
DMARQ#
Table 2: Signal Descriptions for Standard Interface (Mobile DiskOnChip 512Mb G3 7x10 FBGA Package)
Signal
C2, D2, E2, F2
D1, E1, F1, G1
K4, J3, H3, K2
K6, H5, H4
F6, E6, C6
K3, G3, J2
Ball No.
D7, C7
H7, K7
G8, F7
H6, J6
J7, G6
H1
H2
C5
E7
D4
K5
G7
F3
E4
ST, R8 Data bus, high byte. Not used and may be left
Input
Type
OD
OD
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
Preliminary Data Sheet, Rev. 1.1
Address bus. A0 is multiplexed with the DPD ball.
floating when IF_CFG is set to 0 (8-bit mode).
Data bus, low byte.
Chip Enable, active low
Write Enable, active low
Output Enable, active low
Identification. Configuration control to support up to
four chips cascaded in the same memory window.
Chip 1 = ID1, ID0 = VSS, VSS (0,0); must be used
Chip 2 = ID1, ID0 = VSS, VCCQ (0,1)
Chip 3 = ID1, ID0 = VCCQ, VSS (1,0)
Chip 4 = ID1, ID0 = VCCQ, VCCQ (1,1)
Lock, active low. When active, provides full
hardware data protection of selected partitions.
Interface Configuration, 1 (VCCQ) for 16-bit
interface mode, 0 (VSS) for 8-bit interface mode.
Busy, active low, open drain. Indicates that
DiskOnChip is initializing and should not be
accessed. A 10 KΩ pull-up resistor is required if
this ball drives an input. A 10 KΩ pull-up resistor is
recommended even if this ball is not used.
Reset, active low.
System Clock.
DMA Request, active low. A 10 KΩ pull-up resistor
is required if this ball drives an input. A 10 KΩ pull-
up resistor is recommended even if this ball is not
used.
System Interface
Configuration
Control
Description
for single chip configuration
Mobile DiskOnChip G3
91-SR-011-05-8L
Signal
Output
Output
Output
Output
Input/
Input/
Type
Input
Input
Input
Input
Input
Input
Input
Input
Input