TLP700(F) Toshiba, TLP700(F) Datasheet - Page 2

• Manufacturer Part Number: TLP700(F)
• Description: IC PHOTOCOUPLER IRED 6-SDIP
• Manufacturer: Toshiba

Specifications of TLP700(F)

• Voltage - Isolation: 5000Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 2A
• Current - Dc Forward (if): 20mA
• Input Type: DC
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Through Hole
• Package / Case: 6-SDIP (0.300", 7.62mm)
• Configuration: 2 Channel
• Maximum Forward Diode Voltage: 1.75 V
• Maximum Reverse Diode Voltage: 6 V
• Maximum Input Diode Current: 20 mA
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• Isolation Voltage: 5000 Vrms
• Maximum Fall Time: 50 ns
• Maximum Rise Time: 50 ns
• Minimum Forward Diode Voltage: 1.57 V
• Output Device: Integrated Photo IC
• No. Of Channels: 1
• Optocoupler Output Type: Gate Drive
• Input Current: 10mA
• Output Voltage: 35V
• Opto Case Style: DIP
• No. Of Pins: 8
• Operating Temperature Range: -40°C To
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: TLP700F; TLP700F

Absolute Maximum Ratings
Recommended Operating Conditions
Operating frequency
Operating temperature range
Storage temperature range
Lead soldering temperature (10 s)
Isolation voltage (AC, 1 minute, R.H. ≤ 60%)
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
Note 1: Pulse width P
Note 2: Exponential waveform pulse width P
Note 3: Exponential waveform I
Note 4: For the effective lead soldering area
Note 5: Device considered a two-terminal device: pins 1, 2 and 3 paired with pins 4, 5 and 6 respectively.
Note 6: A ceramic capacitor (0.1 μF) should be connected from pin 6 to pin 4 to stabilize the operation of the high
Input current, ON
Input voltage, OFF
Supply voltage *
Peak output current
Operating temperature
* This item denotes operating ranges, not meaning of recommended operating conditions.
Note : Recommended operating conditions are given as a design guideline to obtain expected performance of the
Note 7: Input signal rise time (fall time) ≤ 0.5 μs.
Note 8: If the Vcc rise slope is sharp, an internal circuit might not operate with stability. Please design the Vcc rise
Forward current
Forward current derating (Ta ≥ 85°C)
Peak transient forward current
Reverse voltage
Junction temperature
“H” peak output current
“L” peak output current
Output voltage
Supply voltage
Junction temperature
device. Additionally, each item is an independent guideline respectively. In developing designs using this
product, please confirm specified characteristics shown in this document.
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
gain linear amplifier. Failure to provide the bypassing may impair the switching property.
The total lead length between capacitor and coupler should not exceed 1 cm.
slope under 3.0 V/μs.
Characteristics
Characteristics
W
≤ 1 μs, 300 pps
(Note 8)
(Note 7)
OPH
Ta=-40 to 100 °C
(Ta = 25 °C)
I
≥−1.5 A (≤ 0.3 μs), I
OPH
V
Symbol
I
F (OFF)
F (ON)
T opr
V
(Note 2)
CC
/ I
OPL
(Note 1)
(Note 3)
(Note 4)
(Note 5)
W
≤ 0.3 μs, f ≤15 kHz
−40
Min
7.5
15
⎯
0
2
ΔI
Symbol
OPL
I
I
T opr
T stg
V
T sol
BV
F
OPH
I
OPL
V
V
Typ.
FP
T j
T j
I
/ΔTa
CC
F
f
O
⎯
⎯
⎯
⎯
⎯
R
S
≤+1.5 A (≤ 0.3 μs), Ta=100°C
± 1.5
Max
100
0.8
10
30
−40 to 100
−55 to 125
Rating
−0.54
5000
−2.0
125
125
260
2.0
20
35
35
50
1
5
Unit
mA
°C
V
V
A
mA/°C
Vr m s
Unit
kHz
mA
°C
°C
°C
°C
°C
A
V
A
A
V
V
2009-11-30
TLP700