TOTX141L Toshiba, TOTX141L Datasheet - Page 4
![XMITTER MODULE FIBER OPTIC SHUT](/photos/7/98/79884/totx177l_f_t__totx147l_f_t__totx141l_totx142l_sml.jpg)
TOTX141L
Manufacturer Part Number
TOTX141L
Description
XMITTER MODULE FIBER OPTIC SHUT
Manufacturer
Toshiba
Series
Toslink™r
Datasheet
1.TOTX141.pdf
(6 pages)
Specifications of TOTX141L
Wavelength
650nm
Data Rate
15Mbps
Power - Output
-21 ~ -15dBm
Voltage - Supply
2.7 V ~ 3.6 V
Applications
Digital Audio
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Current - Supply
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TOTX141L
Manufacturer:
TOSHIBA/东芝
Quantity:
20 000
8. Precautions during use
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10) Input voltage
(11) Soldering condition
Maximum rating
Soldering
Support pins
Solvent
Protective cap
Supply voltage
The maximum ratings are the limit values which must not be exceeded during operation of device.
None of these rating value must not be exceeded. If the maximum rating value is exceeded, the
characteristics of devices may never be restored properly. In some extreme cases, the device may be
permanently damages.
Lifetime of light emitters
If an optical module is used for a long period of time, degeneration in the characteristics will mostly
be due to a lowering of the fiber output power (Pf). This is caused by the degradation of the optical
output of the LEDs used as the light source. The cause of degradation of the optical output of the
LEDs may be defects in wafer crystallization or mold resin stress. The detailed causes are, however,
not clear.
The lifetime of light emitters is greatly influenced by the operating conditions and the environment in
which it is used as well as by the lifetime characteristics unique to the device type. Thus, when a light
emitting device and its operating conditions determined, Toshiba recommend that lifetime
characteristics be checked.
Depending on the environment conditions, Toshiba recommend that maintenance such as regular
checks of the amount of optical output in accordance with the condition of the operating environment.
Optical modules are comprised of internal semiconductor devices. However, in principle, optical
modules are optical components. During soldering, ensure that flux does not contact with the emitting
surface or the detecting surface. Also ensure that proper flux removal is conducted after soldering.
Some optical modules come with a protective cap. The protective cap is used to avoid malfunction
when the optical module is not in use. Note that it is not dust or waterproof.
As mentioned before, optical modules are optical components. Thus, in principle, soldering where
there may be flux residue and flux removal after soldering is not recommended. Toshiba recommend
that soldering be performed without the optical module mounted on the board. Then, after the board
has been cleaned, the optical module should be soldered on to the board manually.
If the optical module cannot be soldered manually, use non−halogen (chlorine−free) flux and make
sure, without cleaning, there is no residue such as chlorine. This is one of the ways to eliminate the
effects of flux. In such a cases, be sure to check the devices’ reliability.
Vibration and shock
This module is plastic sealed and has its wire fixed by resin. This structure is relatively resistant to
vibration and shock. In actual equipment, there are sometimes cases in which vibration, shock, or
stress is applied to soldered parts or connected parts, resulting in lines cut. A care must be taken in
the design of equipment which will be subject to high levels of vibration.
The optical transmission module TOTX141 has support pins in order to fix itself to the PCB
temporary. Please make the hole for these pins in the PCB under the condition described in board
layout hole pattern.
Panel attachment
TOTX141 has hole for panel attachment. Please be sure to attach it to panel with self−tapping screw.
When using solvent for flux removal, do not use a high acid or high alkali solvent. Be careful not to
pour solvent in to the optical connector ports. If solvent is inadvertently poured in to them, clean it off
using cotton tips.
When the TOTX141 is not in use, attach the protective cap.
Use the supply voltage within the recommended operating condition (V
that supply voltage does not exceed the maximum rating value of 7 V, even for an instant.
If a voltage exceeding the maximum rating value (V
the internal IC may suffer damage. If there is a possibility that excessive voltage due to surges may
be added to the input terminal, insert a protective circuit.
Solder at 260°C or less for no more than ten seconds.
4
CC
+ 0.5 V) is applied to the transmitter input,
CC
= 2.7~3.6 V). Make sure
2001-08-16
TOTX141