DEMOBOARD TLE 6214L Infineon Technologies, DEMOBOARD TLE 6214L Datasheet - Page 9

• Manufacturer Part Number: DEMOBOARD TLE 6214L
• Description: BOARD DEMO FOR TLE 6214L
• Manufacturer: Infineon Technologies

Specifications of DEMOBOARD TLE 6214L

• Main Purpose: Power Management, Low Side Driver (Internal FET)
• Embedded: No
• Utilized Ic / Part: TLE6214
• Primary Attributes: 2 Channel Internal Switch
• Secondary Attributes: Overvoltage, Short-Circuit & Thermal Protection
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DEMOBOARDTLE6214LIN

No
1
2
3
4
5
6
7
8
SPI Commands:
Command description:
1. Diagnosis Only : Reads out the diagnosis register. This command has no other influence on the
device.
2. Output Configure : Configures the behaviour of the Power Outputs.
3. I/O Configure : Configures the behaviour of the I/O Ports.
V3.0
Command
Diagnosis only
Output Configure
I/O Configure
Reset Registers
Sleep Mode
Wake Up
Channels on (1)
/ off (0)
No command
I
I
Restart / Latch: overtemperature behaviour of the IC
Slew rate: Switching slew rate of channel 1 and 2
Status / SPI : Output of diagnostic information of the IC
Parallel / Serial Input : Control of the output channels
Sense / Fault : Function of the Sense / Fault / ST1 output
lim
lim
bit3 bit2
bit1 bit0
Ch1: overload behaviour of channel 1
Ch2: overload behaviour of channel 2
0
0
1
1
0
0
1
1
0: Current limit 2 is activated (default)
1: Current limit 1 is activated
0: Current limit 2 is activated(default)
1: Current limit 1 is activated
0: Automatic autorestart of a channel after cooling down(default)
1: Latching "off" of a channel at overtemperature
0: fast switching (slew rate 1) (default)
1: slow switching (slew rate 2)
0: Diagnosis output serial with one status output per channel (ST1, ST2)
1: Diagnosis output with SPI (SO) and Fault Pin / Sense Pin
0 : Control of channel 1 and 2 with parallel input (IN1, IN2) (default)
1 : Control of channel 1 and 2 with combination (OR) of serial and
0 : Control of channel 1 and 2 with combination (AND) of serial and
1 : Control of channel 1 and 2 only with SPI
0 : Pin function is "general Fault pin"(default)
1 : Pin function is current sense output channel 1 (I
0 : Pin function is current sense output channel 2 (I
1 : Pin function is current sense output channel 1 + 2 (I
MSB
(default values are bold print)
parallel input signal
parallel input signal
0
0
0
1
1
1
1
0
Command Bits
6
0
1
1
0
0
1
1
0
Page
5
1
0
1
0
1
0
1
0
9
Status /
I
lim
Ch2
SPI
X
X
X
X
X
4
Ch2
I
Parallel / Serial In-
lim
Ch1
X
X
X
X
X
3
Ch1
put
Datasheet TLE 6214 L
IS1
IS2
Data Bits
Restart
/Latch
)
)
X
X
X
X
X
X
2
IS1
+ I
IS2
Slewrate
)
Ch2
Fault / Sense
X
X
X
X
X
X
1
18.10.2004
Slewrate
Ch1
LSB
X
X
X
X
X
X