ISP1582 PCI EVALKIT ST-Ericsson Inc, ISP1582 PCI EVALKIT Datasheet - Page 17

• Manufacturer Part Number: ISP1582 PCI EVALKIT
• Description: PCI BUS EVAL KIT ISP1582
• Manufacturer: ST-Ericsson Inc

Specifications of ISP1582 PCI EVALKIT

• Main Purpose: Interface, USB 2.0 Host/Controller
• Embedded: Yes, FPGA / CPLD
• Utilized Ic / Part: ISP1582
• Primary Attributes: High Speed (480Mbps) Transceiver
• Secondary Attributes: Graphic User Interface
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: Q3735081

USB solutions (continued)
HS, FS, and LS denote high-speed, full-speed, and low-speed data transfer rates, respectively
Product
USB peripheral controllers
PDIUSBD12
ISP1181B
ISP1183
ISP1104 - [FS] Allows selectable differential or single-ended input mode
ISP1105 - [FS, LS] Allows selectable differential or single-ended input
ISP1106 - [FS, LS] Allows differential input mode only
ISP1109 - [FS, LS] Peripheral transceiver supporting carkit standard
ISP1110 - [FS] Bidirectional input mode only
Description
- V
- Supports SPI (up to 26 MHz) and I
- Supports UART pass-through on DP, DM lines
- Supports UART pass-through on DP, DM lines
- V
- Very good for 3.3-V supply voltage
- [FS] USB peripheral controller with 8-bit parallel bus, 6
- 2 MB/s transfer rate: 1 MB/s in Bulk mode, 1 Mb/s in ISO
- Single supply voltage 3.0 to 3.6 V, or 4.0 to 5.5 V
- [FS] USB peripheral controller with 16-bit parallel bus, 16
- Supply voltage 3.0 to 3.6 V, or 4.0 to 5.5 V
- Integrated 5.0-to-3.3-V voltage regulator for bus-power
- [FS] USB peripheral controller with 8-bit parallel data bus, 16
- Integrated 5.0-to-3.3-V voltage regulator for bus-power
- Operating voltage 3.0 to 3.6 V, or 4.0 to 5.5 V
- Dual supply voltages: main 3.0 to 3.6 V, digital I/O interface
mode
CEA-936-A
access control and status registers
endpoints, 320-byte FIFO, bus-powered
mode
endpoints, 2462-byte FIFO for ISO transfer, bus-powered,
max 11.1 MB/s transfer rate to μC or μP
support
endpoints, 2462-byte FIFO for ISO transfer, bus-powered,
max 11.1 MB/s transfer rate to μC or μP
support
1.65 to 3.6 V, enabling direct interface to battery-operated
devices e.g., mobile phones
BUS
BUS
detection input
detection input but not in ‘suspend’ mode
2
C-bus (up to 400 kHz) to
Target applications
Carkit, mobile phone
Mobile phone
Digital camera, printer,
STB, FDD, PDA, MP3
player, router, modem,
USB dongle
Digital camera, printer,
router, modem, CD-RW
drive, FDD, MP3 player,
STB, PDA, USB dongle
Digital camera, mobile
phone, printer, STB, FDD,
PDA, MP3 player, router,
modem, USB dongle
Reference kits
- ISP1104W BCC eval kit
- ISP1105BS eval kit
- ISP1105W BCC eval kit
- ISP1106W BCC eval kit
- ISP1109 eval kit
- ISP1110 eval kit
- D12 ISA PC eval kit
- D12 Smart eval kit
- D12 USB-EPP eval kit
- D12 USB Mass Storage
- ISP1181B PC eval kit
- ISP1181B MCU eval kit
- ISP1181B R232 USB
- ISP1183 PC eval kit
- ISP1183 MCU eval kit
eval kit
eval kit
Application notes
- ISP1109 Firmware Programming Guide
- Using PDIUSBD12 in DMA Mode
- Interfacing D12 to Hitachi H8S/2357
- PDIUSBD12 Frequently Asked Questions
- Interfacing ISP1181 to Hitachi SH7709 RISC Processor
- Interrupt Control in ISP1181x
- Simultaneous DMA and PIO Access in the ISP116x,
- Simultaneous DMA and PIO Access in the ISP116x,
ISP118x and ISP136x Device Controller
ISP118x and ISP136x Device Controller
Continued next page
Package(s)
HBCC16
(SOT639-2)
HBCC16
(SOT639-2)
HVQFN16
(SOT758-1)
TSSOP16
(SOT403-1)
HBCC16
(SOT639-2)
HVQFN32
(SOT617-1)
HBCC16
(SOT639-2)
SO28
(SOT136-1)
TSSOP28
(SOT361-1)
TSSOP48
(SOT362-1)
HVQFN48
(SOT619-2)
HVQFN32
(SOT617-1)
17