AT32UC3L-EK Atmel, AT32UC3L-EK Datasheet - Page 568
AT32UC3L-EK
Manufacturer Part Number
AT32UC3L-EK
Description
KIT EVAL AVR32 UC3 MCU
Manufacturer
Atmel
Type
MCUr
Specifications of AT32UC3L-EK
Contents
*
Silicon Manufacturer
Atmel
Core Architecture
AVR
Core Sub-architecture
UC3L
Kit Contents
Board
Features
USB / Battery Powered, Board Controller / Bootloader
Svhc
No SVHC (15-Dec-2010)
Rohs Compliant
Yes
Tool Type
Starter Kit
Cpu Core
AVR 8
Data Bus Width
8 bit
Processor Series
AT32
Processor To Be Evaluated
AT32UC3L064
Interface Type
USB, Capacitive Touch
For Use With/related Products
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT32UC3L-EK
Manufacturer:
Atmel
Quantity:
135
- Current page: 568 of 858
- Download datasheet (13Mb)
Figure 24-13. WAVSEL = 3 With Trigger
24.6.3.6
24.6.3.7
32099F–11/2010
Waveform Examples
External event/trigger conditions
Output controller
0xFFFF
Counter Value
RB
RA
RC
TIOB
TIOA
An external event can be programmed to be detected on one of the clock sources (XC0, XC1,
XC2) or TIOB. The external event selected can then be used as a trigger.
The External Event Selection field in CMRn (CMRn.EEVT) selects the external trigger. The
External Event Edge Selection field in CMRn (CMRn.EEVTEDG) defines the trigger edge for
each of the possible external triggers (rising, falling or both). If CMRn.EEVTEDG is written to
zero, no external event is defined.
If TIOB is defined as an external event signal (CMRn.EEVT = 0), TIOB is no longer used as an
output and the compare register B is not used to generate waveforms and subsequently no
IRQs. In this case the TC channel can only generate a waveform on TIOA.
When an external event is defined, it can be used as a trigger by writing a one to the
CMRn.ENETRG bit.
As in Capture mode, the SYNC signal and the software trigger are also available as triggers. RC
Compare can also be used as a trigger depending on the CMRn.WAVSEL field.
The output controller defines the output level changes on TIOA and TIOB following an event.
TIOB control is used only if TIOB is defined as output (not as an external event).
The following events control TIOA and TIOB:
RA compare controls TIOA and RB compare controls TIOB. Each of these events can be pro-
grammed to set, clear or toggle the output as defined in the following fields in CMRn:
• software trigger
• external event
• RC compare
• RC Compare Effect on TIOB (CMRn.BCPC)
Counter decremented by compare match
with RC
AT32UC3L016/32/64
Counter decremented by trigger
Counter incremented by trigger
Time
568
Related parts for AT32UC3L-EK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: