AT32UC3L-EK Atmel, AT32UC3L-EK Datasheet - Page 713
AT32UC3L-EK
Manufacturer Part Number
AT32UC3L-EK
Description
KIT EVAL AVR32 UC3 MCU
Manufacturer
Atmel
Type
MCUr
Specifications of AT32UC3L-EK
Contents
*
Silicon Manufacturer
Atmel
Core Architecture
AVR
Core Sub-architecture
UC3L
Kit Contents
Board
Features
USB / Battery Powered, Board Controller / Bootloader
Svhc
No SVHC (15-Dec-2010)
Rohs Compliant
Yes
Tool Type
Starter Kit
Cpu Core
AVR 8
Data Bus Width
8 bit
Processor Series
AT32
Processor To Be Evaluated
AT32UC3L064
Interface Type
USB, Capacitive Touch
For Use With/related Products
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT32UC3L-EK
Manufacturer:
Atmel
Quantity:
135
- Current page: 713 of 858
- Download datasheet (13Mb)
30.6.6
30.6.7
32099F–11/2010
Interrupts
Using the Peripheral DMA Controller
To make the CPU able to do other things while waiting for the aWire UART user interface to fin-
ish its operations the aWire UART user interface supports generating interrupts. All status bits in
the Status Register can be used as interrupt sources, except the SR.BUSY and SR.CENABLED
bits.
To enable an interrupt the user must write a one to the corresponding bit in the Interrupt Enable
Register (IER). Upon the next zero to one transition of this SR bit the aWire UART user interface
will flag this interrupt to the CPU. To clear the interrupt the user must write a one to the corre-
sponding bit in the Status Clear Register (SCR).
Interrupts can be disabled by writing a one to the corresponding bit in the Interrupt Disable Reg-
ister (IDR). The interrupt Mask Register (IMR) can be read to check if an interrupt is enabled or
disabled.
To relieve the CPU of data transfers the aWire UART user interface support using the Peripheral
DMA controller.
To transmit using the Peripheral DMA Controller do the following:
To receive using the Peripheral DMA Controller do the following:
1. Setup the aWire UART user interface in transmit mode.
2. Setup the Peripheral DMA Controller with buffer address and length, use byte as trans-
3. Enable the Peripheral DMA Controller.
4. Wait until the Peripheral DMA Controller is done.
1. Setup the aWire UART user interface in receive mode
2. Setup the Peripheral DMA Controller with buffer address and length, use byte as trans-
3. Enable the Peripheral DMA Controller.
4. Wait until the Peripheral DMA Controller is ready.
fer size.
fer size.
AT32UC3L016/32/64
713
Related parts for AT32UC3L-EK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: