COP8SA-DM National Semiconductor, COP8SA-DM Datasheet - Page 165
COP8SA-DM
Manufacturer Part Number
COP8SA-DM
Description
MODULE DEBUGGING FOR COP8SA
Manufacturer
National Semiconductor
Datasheet
1.DM-COP820D.pdf
(254 pages)
Specifications of COP8SA-DM
Module/board Type
Debugger Module
For Use With/related Products
Cop 8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*COP8SA-DM
- Current page: 165 of 254
- Download datasheet (2Mb)
Instruction Cycle Time (t
External CKI Clock Duty Cycle (Note 6)
Inputs
Output Propagation Delay (Note 5)
MICROWIRE Setup Time (t
MICROWIRE Hold Time (t
MICROWIRE Output Propagation Delay (t
MICROWIRE Maximum Shift Clock
Input Pulse Width (Note 6)
Reset Pulse Width
t
Note 1: Maximum rate of voltage change must be < 0.5 V/ms.
Note 2: Supply and IDLE currents are measured with CKI driven with a square wave Oscillator, CKO driven 180˚ out of phase with CKI,
inputs connected to V
Note 3: The HALT mode will stop CKI from oscillating in the R/C and the Crystal configurations. In the R/C configuration, CKI is forced
high internally. In the crystal or external configuration, CKI is TRI-STATE. Measurement of I
nor sinking current; with L, F, C, G0, and G2-G5 programmed as low outputs and not driving a load; all outputs programmed low and not
driving a load; all inputs tied to V
the G Port data register.
Note 4: Pins G6 and RESET are designed with a high voltage input network. These pins allow input voltages > V
have sink current to V
effective resistance to V
WARNING: Voltages in excess of 14 volts will cause damage to the pins. This warning excludes ESD transients.
Note 5: The output propagation delay is referenced to the end of the instruction cycle where the output change occurs.
Note 6: Parameter characterized but not tested.
C
= Instruction cycle time (Clock Input frequency divided by 10)
Crystal/Resonator, External
Internal R/C Oscillator
(Note 6)
Rise Time (Note 6)
Fall Time (Note 6)
t
t
t
SO, SK
All Others
Master Mode
Slave Mode
Interrupt Input High Time
Interrupt Input Low Time
Timer Input High Time
Timer Input Low Time
R/C Oscillator Frequency Variation
SETUP
HOLD
PD1
, t
PD0
specified)
Parameter
CC
CC
CC
c
when biased at voltages > V
and outputs driven low but not connected to a load.
)
UWH
is 750
UWS
) (Note 5)
) (Note 5)
CC
; WATCHDOG and clock monitor disabled. Parameter refers to HALT mode entered via setting bit 7 of
(typical). These two pins will not latch up. The voltage at the pins must be limited to < 14 Volts.
UPD
)
4.5V
2.7V
4.5V
2.7V
4.5V
2.7V
fr = Max
fr = 10 MHz Ext Clock
fr = 10 MHz Ext Clock
4.5V
2.7V
4.5V
2.7V
R
4.5V
2.7V
4.5V
2.7V
L
= 2.2k, C
CC
(the pins do not have source current when biased at a voltage below V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
Conditions
L
< 4.5V
< 4.5V
< 4.5V
< 4.5V
< 4.5V
< 4.5V
< 4.5V
= 100 pF
5.5V
5.5V
5.5V
5.5V
5.5V
5.5V
5.5V
COP8SAx7 MICROCONTROLLER
A
45
Min
200
500
150
1.0
2.0
DD
60
20
56
1
1
1
1
1
HALT is done with device neither sourcing
TBD
Typ
2.0
55
12
8
CC
TBD
Max
1.75
220
500
DC
DC
0.7
1.0
2.5
and the pins will
35
1
%
ns
ns
CC
Units
MHz
kHz
). The
2-127
%
%
ns
ns
ns
ns
ns
ns
ns
t
t
t
t
c
c
c
c
s
s
s
s
s
s
s
s
s
Related parts for COP8SA-DM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PROGRAMING UNIT FOR COP8SA PARTS
Manufacturer:
National Semiconductor
Part Number:
Description:
ADAPTER SOIC 16,20,28,44 PLCC
Manufacturer:
National Semiconductor
Part Number:
Description:
8-Bit CMOS ROM Based and One-Time Programmable OTP Microcontroller with 1k to 4k Memory/ Power On Reset/ and Very Small Packaging
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [8-Bit D/A Converter]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [Media Coprocessor]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
AC97 Rev 2 Codec with Sample Rate Conversion and National 3D Sound
Manufacturer:
National Semiconductor
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
8-bit 20 MSPS flash A/D converter.
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Low Noise Quad Operational Amplifier
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad Differential Line Receivers
Manufacturer:
National Semiconductor
Datasheet: