COP8SA-DM National Semiconductor, COP8SA-DM Datasheet - Page 83
COP8SA-DM
Manufacturer Part Number
COP8SA-DM
Description
MODULE DEBUGGING FOR COP8SA
Manufacturer
National Semiconductor
Datasheet
1.DM-COP820D.pdf
(254 pages)
Specifications of COP8SA-DM
Module/board Type
Debugger Module
For Use With/related Products
Cop 8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*COP8SA-DM
- Current page: 83 of 254
- Download datasheet (2Mb)
state. Upon triggering the WATCHDOG, the logic will pull the WDOUT (G1) pin low for
an additional 16 tc–32 tc cycles after the signal level on WDOUT pin goes below the lower
Schmitt trigger threshold. After this delay, the device will stop forcing the WDOUT
output low.The WATCHDOG service window will restart when the WDOUT pin goes
high.
A WATCHDOG service while the WDOUT signal is active will be ignored. The state of
the WDOUT pin is not guaranteed on reset, but if it powers up low then the WATCHDOG
will time out and WDOUT will go high.
The Clock Monitor forces the G1 pin low upon detecting a clock frequency error. The
Clock Monitor error will continue until the clock frequency has reached the minimum
specified value, after which the G1 output will go high following 16 t
The Clock Monitor generates a continual Clock Monitor error if the oscillator fails to
start, or fails to reach the minimum specified frequency. The specification for the Clock
Monitor is as follows:
2.14.3 WATCHDOG and Clock Monitor Summary
The following salient points regarding the WATCHDOG and CLOCK MONITOR should
be noted:
Match
Don't Care Mismatch
Mismatch
Don't Care Don't Care
1/t
1/t
• Both the WATCHDOG and CLOCK MONITOR detector circuits are inhibited dur-
• Following RESET, the WATCHDOG and CLOCK MONITOR are both enabled,
• The WATCHDOG service window and CLOCK MONITOR enable/disable option
• The initial WATCHDOG service must match the key data value in the WATCH-
• Subsequent WATCHDOG services must match all three data fields in WDSVR in
Key Data
c
c
ing RESET.
with the WATCHDOG having he maximum service window selected.
can only be changed once, during the initial WATCHDOG service following RE-
SET.
DOG Service register WDSVR in order to avoid a WATCHDOG error.
order to avoid WATCHDOG errors.
> 10 kHz—No clock rejection.
< 10 Hz—Guaranteed clock rejection.
Match
Don't Care
Window Data
Match
Don't Care Error: Generate WATCHDOG Output
Don't Care Error: Generate WATCHDOG Output
Mismatch
Monitor
Clock
Valid Service: Restart Service Window
Error: Generate WATCHDOG Output
COP8SAx7 MICROCONTROLLER
Action
c
–32 t
c
clock cycles.
2-45
Related parts for COP8SA-DM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PROGRAMING UNIT FOR COP8SA PARTS
Manufacturer:
National Semiconductor
Part Number:
Description:
ADAPTER SOIC 16,20,28,44 PLCC
Manufacturer:
National Semiconductor
Part Number:
Description:
8-Bit CMOS ROM Based and One-Time Programmable OTP Microcontroller with 1k to 4k Memory/ Power On Reset/ and Very Small Packaging
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [8-Bit D/A Converter]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [Media Coprocessor]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
AC97 Rev 2 Codec with Sample Rate Conversion and National 3D Sound
Manufacturer:
National Semiconductor
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
8-bit 20 MSPS flash A/D converter.
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Low Noise Quad Operational Amplifier
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad Differential Line Receivers
Manufacturer:
National Semiconductor
Datasheet: