ATMEGA168-20PU Atmel, ATMEGA168-20PU Datasheet - Page 51

• Manufacturer Part Number: ATMEGA168-20PU
• Description: IC AVR MCU 16K 20MHZ 28DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA168-20PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Processor Series: ATMEGA16x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: 2-Wire, SPI, USART, Serial
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 6 Channel
• A/d Inputs: 6-Channel, 10-Bit
• Cpu Speed: 20 MIPS
• Eeprom Memory: 512 Bytes
• Input Output: 23
• Interface: I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin PDIP
• Programmable Memory: 16K Bytes
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 4.5-5.5 V
• Controller Family/series: AVR MEGA
• No. Of I/o's: 23
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2545E–AVR–02/05
Note: If the Watchdog is accidentally enabled, for example by a runaway pointer or brown-out
condition, the device will be reset and the Watchdog Timer will stay enabled. If the code is not
set up to handle the Watchdog, this might lead to an eternal loop of time-out resets. To avoid this
situation, the application software should always clear the Watchdog System Reset Flag
(WDRF) and the WDE control bit in the initialisation routine, even if the Watchdog is not in use.
The following code example shows one assembly and one C function for changing the time-out
value of the Watchdog Timer.
Note:
Note: The Watchdog Timer should be reset before any change of the WDP bits, since a change
in the WDP bits can result in a time-out when switching to a shorter time-out period.
Assembly Code Example
C Code Example
WDT_Prescaler_Change:
void WDT_Prescaler_Change(void)
{
}
; Turn off global interrupt
cli
; Reset Watchdog Timer
wdr
; Start timed sequence
lds r16, WDTCSR
ori
sts WDTCSR, r16
; --
; Set new prescaler(time-out) value = 64K cycles (~0.5 s)
ldi
sts WDTCSR, r16
; --
; Turn on global interrupt
sei
ret
__disable_interrupt();
__watchdog_reset();
/* Start timed
WDTCSR |= (1<<WDCE) | (1<<WDE);
/* Set new prescaler(time-out) value = 64K cycles (~0.5 s) */
WDTCSR
__enable_interrupt();
1.
See ”About Code Examples” on page 6.
r16, (1<<WDCE) | (1<<WDE)
Got four cycles to set the new values from here -
r16, (1<<WDE) | (1<<WDP2) | (1<<WDP0)
Finished setting new values, used 2 cycles -
= (1<<WDE) | (1<<WDP2) | (1<<WDP0);
(1)
(1)
equence */
ATmega48/88/168
51